Liebherr 230311 7084644-00 ユーザーズマニュアル

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What

is  more,  the  door  may  not  close  and  therefore  the  appliance

may fail to cool properly.

u

Screw the turn hinges firmly into place with 4 Nm.

u

Check all of the screws and retighten if necessary.

Fig. 9 

(1) Stack cabinet

(3) Kitchen cabinet

(2) Appliance

(4) Wall

The appliance can be inserted into a row of kitchen units. To

match the appliance

 Fig. 9 (2)

 to the height of the row of units,

a suitable stack cabinet

 Fig. 9 (1)

 can be fitted above the appli-

ance.
When inserting the appliance into a row of kitchen units (max.

depth 580 mm), the appliance can be installed directly next to

the kitchen unit

 Fig. 9 (3)

. The appliance door projects relative

to  the  front  of  the  kitchen  unit  by  34  mm   at  the  side  and  by

50  mm  in  the  middle  of  the  appliance.  It  can  be  opened  and

closed perfectly as a result.
Important for the ventilation:

-

At the back of the stack cabinet there has to be a ventilation

duct  of  at  least  50  mm  depth  throughout  the  width  of  the

stack cabinet.

-

The  ventilation  space  under  the  ceiling  has  to  be  at  least

300 cm

2

.

-

The larger the ventilation space, the more energy-saving the

appliance is in operation.

If  the  appliance  is  installed  with  the  hinges  next  to  a  wall

Fig. 9 (4)

, the distance between appliance and wall has to be at

least 40 mm. This corresponds to the projection of the handle

when the door is open.

Danger of suffocation due to packing material and plastic film!

u

Do not allow children to play with packing material.

The packaging is made of recyclable materials:

-

corrugated board/cardboard

-

expanded polystyrene parts

-

polythene bags and sheets

-

polypropylene straps

-

nailed wooden frame with polyethylene panel*

u

Take the packaging material to an official collecting point.

Risk of damage to the electronic control system!

u

Do not use stand-alone inverters (conversion of d.c. to a.c./

three-phase) or energy saving plugs.

Fire and overheating hazard!

u

Do not use extension cables or multiple socket outlets.

The  type  of  current  (alternating  current)  and  voltage  at  the

installation site have to conform with the data on the type plate

(see Appliance at a glance).

Connect the appliance only with a properly installed

socket outlet with earthing contact. The socket outlet

must be fused with 10 A or higher.
It must be easily accessible so that the appliance can

be quickly disconnected from the supply in an emer-

gency. It must be outside the area of the rear of the

appliance.

u

Check the electrical connection.

u

Plug in the power plug.

Put  the  appliance  into  operation  about  2  hours  before  first

loading food to be frozen.
Do  not  load  food  to  be  frozen  before  the  temperature  display

reads -18 °C.
u

Press On/Off button

 Fig. 3 (7)

.

w

The interior light is on when the door is open.

You can adjust the brightness of the temperature display to the

light conditions of the room in which the appliance is installed.

The brightness is adjustable between h0 (no illumination) and

h5 (maximum luminosity).

u

To  activate  the  setting  mode:  press  the  SuperFrost  button

Fig. 3 (8)

 for about 5 s.

w

The display indicates c.

w

The menu symbol

 Fig. 3 (3)

 shines.

u

Using  the  Up  setting  button

  Fig.  3  (1)

  or  Down  setting

button,

 Fig. 3 (2)

, select h.