Mitsubishi Electronics FR-F700-NA ユーザーズマニュアル

· To prevent a malfunction due to noise, keep the signal cables more than 10cm (3.94inches) away from the power cables. Also

separate the main circuit wire of the input side and the output side.

· After wiring, wire offcuts must not be left in the inverter.

Wire offcuts can cause an alarm, failure or malfunction. Always keep the inverter clean.

When drilling mounting holes in an enclosure etc. take care not to allow chips and other foreign matter to enter the inverter.

· Set the voltage/current input switch correctly. Operation with a wrong setting may cause a fault, failure or malfunction.

Three-phase AC 

power supply

MCCB

Jumper

10E(+10V)

10(+5V)

Control input signals (No voltage input allowed)

Jumper

Motor

Relay output 1
(Fault output)

*1

Main circuit terminal

Control circuit terminal

MC

Relay output 2

Relay output

IM

SINK

SOURCE

Terminal functions 
vary with the output 
terminal assignment 
(

Terminal functions 
vary with the output 
terminal assignment 
(

Terminal functions vary 
with the input terminal 
assignment 
(

Pr. 178 to Pr. 189)

*3

EMC filter
ON/OFF
connector

ON

OFF

Frequency setting signal (Analog)

Frequency setting

 potentiometer

1/2W1k

Ω

Auxiliary

input

(Analog common)

0 to 5VDC
0 to 10VDC

selectable

selectable

selectable

0 to 20mADC

*4

PU
connector

 Terminal 

4 input

(Current

input)

Connector 
for plug-in option 
connection

*5.  It is recommended to use 

2W1k

Ω when the 

frequency setting signal is 
changed frequently. 

0 to 5VDC
0 to 10VDC

*4

RS-485 terminals

Data transmission

Data reception

4 to 20mADC

*4

0 to 

±5VDC

0 to 

±10VDC

(-)

(+)

(0 to 10VDC)

Analog signal output

Frequency detection

Open collector output common
Sink

/source common

Running

Up to frequency

Instantaneous 
power failure

Overload

Open collector output

Terminal 4 input selection

(Current input selection)

Selection of automatic restart 

after instantaneous 

power failure

Output stop

Reset

*3.  AU terminal can be 

used as PTC input 
terminal.

Middle speed

High speed

Low speed

Jog operation

Second function selection

Multi-speed 
selection

Forward

rotation

start

Reverse

rotation

start

Start self-holding selection

Jumper

*7.

*5

(Permissible load 
current 100mA)

*2.  To supply power to the 

control circuit separately, 
remove the jumper across 
R1/L11 and S1/L21.

*2

Do not use PR and PX terminals. 
Please do not remove the jumper 
connected to terminal PR and PX.

Initial

value

Initial

value

Initial value

*4.  Terminal input specifications 

can be changed by analog 
input specifications switchover 
(

Pr. 73, Pr. 267). Set the 

voltage/current input switch in 
the OFF position to select 
voltage input (0 to 5V/0 to 
10V) and ON to select current 
input (0 to 20mA).

ON

4 2

OFF

Voltage/current 

input switch

*4

Resistor unit
(Option)

Brake unit
(Option)

Inrush current 

limit circuit

Sink logic

Ground

Ground 

Ground 

(0 to 20mADC)

(-)

(+)

(-)

(+)

Analog current output

(-)

(+)

24VDC power supply

(Common for external power supply transistor)

Contact input common

 

*6. A CN8 (for MT-BU5) connector is  
     provided for the FR-F720-03160 
     (FR-F740-01800) or more.

*1. 

DC reactor (FR-HEL)
Be sure to connect the DC reactor 
supplied with the FR-F720-03160
(FR-F740-01800) or more. 

When a DC reactor is connected to
the 02330 (FR-F740-01160) or less, 
remove the jumper across P1 and P/+.

*8. The 200V class 00046 and 00077  

are not provided with the ON/OFF 
connector EMC filter. 

*8

Option connector 1

Option connector 2