Roland juno-stage ユーザーガイド
152
Chapter 11. Other Settings
[2 (GENERL)]
[3 (SYNTH)]
System Menu [6 (D BEAM)]
Parameter
Value
Explanation
Sensitivity
D Beam Sens
0–127
This sets the D Beam controller’s sensitivity.
Increasing this value will make the D Beam controller more responsive.
Parameter
Value
Explanation
Level & Range
Level
Level
0–127
Volume Level of the Solo Synth
Chorus Send Level
0–127
Level of the signal sent to chorus
Reverb Send Level
0–127
Level of the signal sent to reverb
Range
2OCT, 4OCT, 8OCT
Range in which the pitch of the solo synth will vary
Osc1
Osc 1 Waveform
SAW, SQR
Waveform
SAW:
Sawtooth wave
SQR:
Square wave
Osc 1 Pulse Width
0–127
Pulse width of the waveform
By cyclically modifying the pulse width you can create subtle changes in the tone.
Osc 1 Coarse Tune
-48–+48
Pitch of the tone’s sound (in semitones, +/-4 octaves)
Osc 1 Fine Tune
-50–+50
Pitch of the tone’s sound (in 1-cent steps)
Osc2 & Sync
Osc 2 Waveform
Osc 2 Waveform
(same as Osc 1)
Osc 2 Pulse Width
Osc 2 Coarse Tune
Osc 2 Fine Tune
Osc 2 Level
Osc 2 Coarse Tune
Osc 2 Fine Tune
Osc 2 Level
0–127
Level of the OSC2
Osc Sync Switch
OFF, ON
Turning this switch on produces a complex sound with many harmonics.
This is effective when the OSC1 pitch is higher than the OSC2 pitch.
Filter
Filter Type
OFF, LPF, BPF, HPF,
PKG
PKG
Type of filter
OFF:
No filter is used.
LPF:
Low Pass Filter. This reduces the volume of all frequencies above the cutoff frequency
(Cutoff) in order to round off, or un-brighten the sound.
BPF:
Band Pass Filter. This leaves only the frequencies in the region of the cutoff frequency,
and cuts the rest.
HPF:
High Pass Filter. This cuts the frequencies in the region below the cutoff frequency.
PKG:
Peaking Filter. This emphasizes the frequencies in the region of the cutoff frequency.
Cutoff
0–127
Frequency at which the filter begins to have an effect on the waveform’s frequency components
Resonance
0–127
Emphasizes the portion of the sound in the region of the cutoff frequency, adding character to
the sound.
the sound.
LFO
LFO Rate
LFO Rate
0–127
Modulation speed of the LFO
LFO Osc 1 Pitch Depth
-63–+63
Depth to which the LFO will modulate the Osc 1 pitch
LFO Osc 2 Pitch Depth
-63–+63
Depth to which the LFO will modulate the Osc 2 pitch
LFO Osc 1 Pulse Width
Depth
Depth
-63–+63
Depth to which the LFO will modulate the pulse width of the Osc 1 waveform
* The Pulse Width is activated when “SQR” is selected with Osc 1 waveform.
LFO Osc 2 Pulse Width
Depth
Depth
-63–+63
Depth to which the LFO will modulate the pulse width of the Osc 2 waveform
* The Pulse Width is activated when “SQR” is selected with Osc 2 waveform.
JUNO-STAGE_e.book 152 ページ ２００８年１０月１７日 金曜日 午後１２時２７分