Roland RS-70 オーナーマニュアル
120
Using the floppy disk drive
6.
Press PAGE/CURSOR [
] to go to the next page.
Use VALUE [-]/[+] to select the file that contains the patch(es) or
rhythm set(s) you want to load.
rhythm set(s) you want to load.
fig.r11-06_40
The file name will depend on the file you are loading.
7.
Press PAGE/CURSOR [
] to go to the next page.
When loading user patches:
Use VALUE [-]/[+] to specify the first (001–128) of the patch
numbers you want to load.
numbers you want to load.
fig.r11-07_40
When loading user rhythm sets:
Use VALUE [-]/[+] to specify the first (01–16) of the rhythm set
numbers you want to load.
numbers you want to load.
fig.
8.
Use PAGE/CURSOR [
] to move the cursor.
When loading user patches:
Use VALUE [-]/[+] to specify the last (001–128) of the patch
numbers you want to load.
numbers you want to load.
fig.r11-08_40
When loading user rhythm sets:
Use VALUE [-]/[+] to specify the last (01–16) of the rhythm set
numbers you want to load.
numbers you want to load.
fig.
9.
Press PAGE/CURSOR [
] to go to the next page.
When loading user patches:
Use VALUE [-]/[+]to specify the first number (001–128) of the
destination for the load.
destination for the load.
fig.r11-09_40
When loading user rhythm sets:
Use VALUE [-]/[+]to specify the first number (01–16) of the
destination for the load.
destination for the load.
fig.r11-09_40
10.
Press [ENTER].
The range of patches you specified in step 7 will be loaded,
starting at the number you specified as the load destination.
starting at the number you specified as the load destination.
If you decide to cancel, press [EXIT].
When the data has been loaded, the display will indicate
“COMPLETED.” This ends the procedure.
“COMPLETED.” This ends the procedure.
Loading SMF data
Here’s how SMF data saved on disk can be loaded into the current
pattern. You can edit and save the loaded data just like an ordinary
pattern.
pattern. You can edit and save the loaded data just like an ordinary
pattern.
You can load either format 0 or 1.
1.
Insert a disk into the floppy disk drive.
2.
Press [WRITE] while holding down [SHIFT].
3.
Use PAGE/CURSOR [
]/[
] to select “1:LOAD.”
fig.r11-10_40
4.
Press [ENTER].
5.
Use VALUE [-]/[+] to select “Type:SMF.”
fig.r11-11_40
6.
Press PAGE/CURSOR [
] to go to the next page.
Use VALUE [-]/[+] to select the SMF that you want to load into
the current pattern.
the current pattern.
fig.r11-12_40
The file name will depend on the file you are loading.
7.
Press [ENTER].
If you decide to cancel, press [EXIT].
When the data has been loaded, the display will indicate
“COMPLETED.” This ends the procedure.
“COMPLETED.” This ends the procedure.
Now, when you press [PATTERN], you will enter Pattern mode,
where you can edit or save the loaded SMF in the same way as a
conventional pattern.
where you can edit or save the loaded SMF in the same way as a
conventional pattern.
fig.r11-12a_40
Saving data on disk (SAVE)
Saving the entire user memory
Here’s how an image of all data in the user area can be saved to disk
as one file.
as one file.
Data cannot be saved to the master disks of Standard MIDI File
releases, etc. from Roland.
releases, etc. from Roland.
1.
Insert a disk into the floppy disk drive.
2.
Press [WRITE] while holding down [SHIFT].
This means you are changing the pattern settings.
RS-70_e4.book 120 ページ ２００３年８月１８日 月曜日 午前９時４７分