Marantz ud9004 ユーザーガイド

28

ENGLISH

G

Crossover  Freq.H  :  Set  the  upper  limit  of  the  low  frequency  signals 

output from the subwoofer.

 

• 

:  Outputs  at  below  set  frequency,  each  speaker’s  bass  signal 
output from the subwoofer. Set this according to the low frequency 
reproduction capabilities of the speakers you are using.
 

• 

Advanced  :  Set  the  low  frequency  signals  to  be  output  from  the 
signals of the respective speakers to the subwoofer.
Front, Center, Surround, Surr. Back

When, on the GUI menu, “Audio Setup” – “7.1ch Audio Out”– “Multi 
Channel”  –  “Speaker  Configuration”  –  “Subwoofer”  is  set  to  “Yes” 
(vpage 27), you can select “LFE” or “LFE+Main”. 

Select  “Large”  or  “Small”  not  according  to  the  physical  size  of  the 

• 

speaker but according to the low frequency reproduction capabilities 
based on the frequency set at “Crossover Freq.”.
On the GUI menu, if the “Audio Setup” – “7.1ch Audio Out”– “

• 

Multi 

Channel”  –  “Speaker  Configuration”  item  setting  is  changed,  other 
settings are automatically changed as well.
G

ExampleH

If you set “Front” to “Small”, “Subwoofer” is set to “Yes” and “Large” 
cannot be selected for “Center”, “Surround” and “Surr. Back”.
Audio  signal  (sampling  frequency,  number  of  channels)  from  the 

• 

HDMI output terminal may be restricted by the specification of the 
HDMI  audio that can be input by the device at the other side.
G

ExampleH

If the HDMI audio specification of the device at the other side is the 
5.1 channel, even when UD9004 plays back by the 7.1 channel, the 
5.1  channel  audio  is  automatically  output.  In  that  case,  the  analog 
audio output becomes the 5.1 channel output as well.

n

 

Channel Level : Set the volume of the test tone to be the same when 

it is output from each speaker. 

G

ModeH : Select a test tone output method.

• 

 : Automatically switch the test tone output speaker.

• 

 Manually switch the test tone output speaker.

G

StartH : Begin outputting the test tone.

When the test tone output stops, press 

 

b

button.

G

SW +10dBH : Increase the subwoofer output level by 10 dB. z

• 

 : Do not change the subwoofer output level.

• 

 Increase the subwoofer output level by +10 dB.

G

DefaultH : Reset all channel level settings to factory default.

• 

 Do not Reset.

• 

 Reset.

n

 

Distance : Set the distance between the listening position and each 

speaker.

G

FeetH or GMetersH : Set the unit of distance.

G

StepH : Set the minimum variable width of the distance.

G

DefaultH : Reset all distance settings to factory default.

Surr.  Back  L  /  Surr.  Back  R  :  Select  the  speaker  you  want  to  set, 
and  set  the  distance.  Set  the  value  that  is  closest  to  the  measured 
distance.
0~60ft or 0~18m

Default settings :

• 

Front/Center/Subwoofer : 3.6 meters (12 feet)
Surround/Surr. Back : 3.0 meters (10 feet)
Set the difference in the distance betweem the speakers to less than 

• 

6.0  meters (20 feet).

Subwoofer Mode
Set the type of low frequency 
signal to be output from the 
subwoofer.

LFE : Add the low frequency signal of the channel for which the speaker 
size is set to “small” to the subwoofer signal and output it.
LFE+Main : Add the low frequency signal of all channels to the subwoofer 
signal and output it.

z

 : “SW +10dB” cannot be set for “HDMI Setup” – “Audio Setup” – “Multi LPCM BM On” – “Channel 

Level” on the GUI menu.

SET UP :

Displaying the menu

 Cancel the menu

d f 0 1 :

Moves the cursor 

 (Up/Down/Left/Right)

:Decision the setting

:Return to previous menu