Electrolux EW30ES65GS インストール手順
5
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS
Canada Style
Figure 2
1.
Power Supply Cord Kit (U.S.A.)
The user is responsible for connecting the power supply
cord to the connection block located behind the back
panel access cover.
cord to the connection block located behind the back
panel access cover.
This appliance may be connected by means of
permanent "hard wiring"; flexible armored or
nonmetallic shielded copper cable (when local code
allow it) or by means of a power supply cord kit. See
chart (on next page) for the minimum wire size (general
UL listing, local code may differ).
permanent "hard wiring"; flexible armored or
nonmetallic shielded copper cable (when local code
allow it) or by means of a power supply cord kit. See
chart (on next page) for the minimum wire size (general
UL listing, local code may differ).
NOTE: Electric Slide-in Range is shipped from factory
with 1 1/8" (2.9 cm) dia. hole as shown on figure 4. If a
larger hole is required, punch out the knockout.
with 1 1/8" (2.9 cm) dia. hole as shown on figure 4. If a
larger hole is required, punch out the knockout.
Risk of fire or electrical shock exists if
an incorrect size range cord kit is used, the
Installation Instructions are not followed, or the
strain relief bracket is discarded.
Installation Instructions are not followed, or the
strain relief bracket is discarded.
For mobile homes, new installations or recreational
vehicles, use only a power supply kit designed for a
range at 125V/250V 50A. Cord must have either 3
(when local code permits grounding through neutral) or 4
conductors. Terminal on end of wires must be either
closed loop or open spade lug with upturned ends. Cord
must have strain-releif clamp. See chart for the minimum
wire size (general UL listing , local code may differ).
vehicles, use only a power supply kit designed for a
range at 125V/250V 50A. Cord must have either 3
(when local code permits grounding through neutral) or 4
conductors. Terminal on end of wires must be either
closed loop or open spade lug with upturned ends. Cord
must have strain-releif clamp. See chart for the minimum
wire size (general UL listing , local code may differ).
Do not loosen the nuts which secure
the factory-installed range wiring to terminal block
while connecting range. Electrical failure or loss of
electrical connection may occur.
while connecting range. Electrical failure or loss of
electrical connection may occur.
2.
Factory Connected Power Supply
Cord (Canada only)
This range is equipped with a factory-connected power
cord (see Figure 2). Cord must be connected to a
grounded 120/240 volt or 120/208 volt range outlet with
a 50A recommended circuit. If no outlet is available,
have one installed by a qualified electrician.
cord (see Figure 2). Cord must be connected to a
grounded 120/240 volt or 120/208 volt range outlet with
a 50A recommended circuit. If no outlet is available,
have one installed by a qualified electrician.
Appliance Rating Watts
120V / 208V
0 - 3120
3121 - 3900
3901 - 4160
4161 - 5200
5201 - 5570
5571 - 7430
7431 - 7800
7801 - 12500
12501 - 14500
Minimum Conductor Size, AWG
L1 and L2
Conductors
16
16
14
14
12
12
12
10
8
Neutral
Conductor
16
16
16
16
16
14
12
12
12
Ground
Conductor
14
12
12
10
10
10
10
10
10
Appliance Rating Watts
120V / 240V
0 - 3600
3601 - 4500
4501 - 4800
4801 - 6000
6001 - 6425
6426 - 8749
8750 - 14500
14501 - 16500
16501 - 24000
Minimum Conductor Size, AWG
L1 and L2
Conductors
16
16
14
14
12
12
10
10
8
Neutral
Conductor
16
16
16
16
16
12
12
10
10
Ground
Conductor
14
12
12
10
10
10
10
10
8
Electrical Shock Hazard
• Electrical ground is required on this appliance.
• Do not connect to the electrical supply until
• Do not connect to the electrical supply until
appliance is permanently grounded.
• Disconnect power to the circuit breaker or fuse
box before making the electrical connection.
• This appliance must be connected to a
grounded, metallic, permanent wiring system,
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.
or a grounding connector should be connected
to the grounding terminal or wire lead on the
appliance.
Failure to do any of the above could result in a
fire, personal injury or electrical shock.
Serial Plate Location
You will find the model and
serial number printed on the
serial plate. The serial plate is
located as shown.
serial number printed on the
serial plate. The serial plate is
located as shown.
Remember to record the
serial number for future
reference.
serial number for future
reference.