Integra cdc-3.1 取り扱いマニュアル
7
R
L
COMPACT DISC CHANGER
MODEL NO.
CDC-3.1
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
AVIS
REMOTE
CONTROL
D IG I TAL
OUTPUT
OPTICAL
ANALOG
OUTPUT
AC INLET
System Connections
Connecting to an audio system
Two types of output jacks are located on the rear panel.
Use the DIGITAL OUTPUT jack if you are connecting the
unit to audio equipment that supports a digital connec-
tion.
Use the DIGITAL OUTPUT jack if you are connecting the
unit to audio equipment that supports a digital connec-
tion.
ANALOG OUTPUT jacks:
These are the most commonly used jacks. Connect these
jacks to the amplifier’s CD input jacks using the supplied
audio connection cable.
These are the most commonly used jacks. Connect these
jacks to the amplifier’s CD input jacks using the supplied
audio connection cable.
DIGITAL OUTPUT (optical) jack:
For digital recording, connect this jack to the digital input
jack of a Mini Disc recorder, a DAT deck, or other digital
equipment. If your amplifier has a digital input jack, con-
necting the DIGITAL OUTPUT jack to it will produce a much
clearer and more dynamic sound.
For digital recording, connect this jack to the digital input
jack of a Mini Disc recorder, a DAT deck, or other digital
equipment. If your amplifier has a digital input jack, con-
necting the DIGITAL OUTPUT jack to it will produce a much
clearer and more dynamic sound.
•
Terminal protection cap is attached to the digital jack.
Remove the cap when connecting the unit to other
digital equipment. When you are not using the digital
output jack, replace the cap.
Remove the cap when connecting the unit to other
digital equipment. When you are not using the digital
output jack, replace the cap.
•
Refer to the amplifier’s instruction manual for connec-
tions.
tions.
•
On each pair of input or output jacks, the jack marked R corresponds to the right channel and the jack marked L
corresponds to the left channel.
corresponds to the left channel.
Connections for remote control (
)
When connecting Integra/Onkyo products, it is necessary
to attach the
to attach the
cable to be able to use the remote con-
troller of the main component to control the entire sys-
tem.
1. To use this CD changer with an amplifier (or receiver),
tem.
1. To use this CD changer with an amplifier (or receiver),
cassette tape deck, and tuner that include the ap-
propriate
propriate
jack, connect the components using the
cable, plugged into the REMOTE CONTROL jacks.
2. As the exact connection sequence of the
cable is
unimportant, you can connect from the amplifier (or
receiver) to either the tuner, cassette tape deck, or
compact disc changer.
receiver) to either the tuner, cassette tape deck, or
compact disc changer.
3. To operate correctly, the remote controller must point
toward the remote control sensor of the amplifier (or
receiver).
receiver).
Audio
connection
cable
connection
cable
Optical fiber
cable (not
included)
cable (not
included)
cable
L
R
CD
Optical IN
DAT, MD recorder or
Digital amplifier
Amplifier
To wall
outlet
outlet
Do not plug in the power
cable until all connections
have been made.
cable until all connections
have been made.
Connecting a power cable
Before plugging in the unit, confirm that all connections
have been made properly.
1. Connect the outlet plug on the included power cable
have been made properly.
1. Connect the outlet plug on the included power cable
to the AC INLET on the CDC-3.1.
2. Plug-in the other end of the cable to a wall AC outlet.
Notes:
•
Do not use any power cable other than the included
cable. The included cable is designed for use only with
the CDC-3.1. Do not use it for any other device.
cable. The included cable is designed for use only with
the CDC-3.1. Do not use it for any other device.
•
Do not connect or disconnect the outlet plug from the
CDC-3.1 while the other end is plugged into the wall
AC outlet.
CDC-3.1 while the other end is plugged into the wall
AC outlet.
Turning on the unit
Press the Power button to the On position.
•
When the power first turns on, the carousel rotates to
find a disc and stops automatically if there is a disc on
the disc tray.
find a disc and stops automatically if there is a disc on
the disc tray.
Power
On
Off
Notes:
•
The upper and lower
REMOTE CONTROL jacks have
the same function.
•
Remote controller operation is not possible when only
the
the
cable is connected – the audio connection
cables must also be connected.
•
An
cable equipped with a 3.5mm (1/8 in.) diam-
eter miniature two-conductor phone plug is included
with this unit and with every tuner and cassette tape
deck that utilizes the
with this unit and with every tuner and cassette tape
deck that utilizes the
jack.
CDC-3.1_05-07
09/05/2000, 4:24 PM
7