Viking Range vgbq0302t インストール手順
26
3/8”
3/8”
male
male
male
flare
flare
flare
adapter
adapter
adapter
3/8”
male
flare
adapter
male
flare
adapter
Type 1,
QCC-1
connector
QCC-1
connector
3/8” female
flare adapter
3/8” male
flare adapter
flare adapter
Regulator
assembly
NOTE: Tank must be
mounted in vertical position
for proper Ventilation
mounted in vertical position
for proper Ventilation
LP/Propane Tank Connection
conducting Propane
and Natural Gas CAN1-
8.3 standard. (See
LP/Propane tank
requirements below). Each
tank is supplied with a dust
cap. Place dust cap on
cylinder valve outlet whenever the
cylinder is not in use. Only install the
type of dust cap on the cylinder valve
outlet that is provided with the cylinder
valve. Other types of caps or plugs may
result in leakage of propane.
and Natural Gas CAN1-
8.3 standard. (See
LP/Propane tank
requirements below). Each
tank is supplied with a dust
cap. Place dust cap on
cylinder valve outlet whenever the
cylinder is not in use. Only install the
type of dust cap on the cylinder valve
outlet that is provided with the cylinder
valve. Other types of caps or plugs may
result in leakage of propane.
Connect the regulator to the grill unit by
screwing the 3/8” flare coupling to the
3/8” flare adapter. Connect to the tank
valve by screwing the Type 1, QCC-
screwing the 3/8” flare coupling to the
3/8” flare adapter. Connect to the tank
valve by screwing the Type 1, QCC-
Connection
Operating Pressure
1/2” (1.3 cm) NPT male with a 3/8”
(.95) flare adapter
10.0” W.C.P. LP/Propane.
Outdoor grills orificed for use with
LP/Propane gas come equipped with a high
capacity hose/regulator assembly for
connection to a standard 20 lb. LP/Propane
cylinder equipped with a Type 1, QCC-1
connector. Hose assembly must comply with
Elastomeric Composite Hose and Couplings
for conducting Propane and Natural Gas,
CAN/CGA-8.1 standard or the Theromplastic
Hose and Hose Couplings for
LP/Propane gas come equipped with a high
capacity hose/regulator assembly for
connection to a standard 20 lb. LP/Propane
cylinder equipped with a Type 1, QCC-1
connector. Hose assembly must comply with
Elastomeric Composite Hose and Couplings
for conducting Propane and Natural Gas,
CAN/CGA-8.1 standard or the Theromplastic
Hose and Hose Couplings for
connector to the LP/Propane tank. Open the
tank valve and check the connection between
the regulator and the Type 1, QCC-1 fitting
for leaks with a soapy water solution. If
bubbles appear, tighten the connection.
Repeat until all leaks have been stopped.
ALWAYS CHECK FOR LEAKS AFTER EVERY
LP/PROPANE TANK CHANGE. Any joint
sealant used must be an approved type and
be resistive to the actions of LP/Propane gas.
tank valve and check the connection between
the regulator and the Type 1, QCC-1 fitting
for leaks with a soapy water solution. If
bubbles appear, tighten the connection.
Repeat until all leaks have been stopped.
ALWAYS CHECK FOR LEAKS AFTER EVERY
LP/PROPANE TANK CHANGE. Any joint
sealant used must be an approved type and
be resistive to the actions of LP/Propane gas.
25
A dented or rusty LP/Propane tank may be
hazardous and should be checked by your
tank supplier. Never use a cylinder with a
damaged valve. All tanks should be equipped
with
hazardous and should be checked by your
tank supplier. Never use a cylinder with a
damaged valve. All tanks should be equipped
with
an
OPD
(overfilling
protection
device). This is a DOT requirement for all
tanks purchased after October 1, 1998 and
will ensure that the tank is not overfilled. The
LP/Propane tank should be a standard 5-gal,
20 lb. gas cylinder tank approximately 12” in
diameter and 18” high which must be
constructed and marked in accordance with
the Specifications for LP/Propane Gas
Cylinders of the U.S. Department of
Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339,
Cylinders,
tanks purchased after October 1, 1998 and
will ensure that the tank is not overfilled. The
LP/Propane tank should be a standard 5-gal,
20 lb. gas cylinder tank approximately 12” in
diameter and 18” high which must be
constructed and marked in accordance with
the Specifications for LP/Propane Gas
Cylinders of the U.S. Department of
Transportation (D.O.T.) or the National
Standard of Canada, CAN/CSA-B339,
Cylinders,
Spheres
and
Tubes
for
Transportation of Dangerous Goods; and
Commission. The cylinder connection device
must be compatible with the Type 1, QCC-1
connector on the outdoor cooking appliance.
Commission. The cylinder connection device
must be compatible with the Type 1, QCC-1
connector on the outdoor cooking appliance.
All LP/Propane tanks must be mounted in a
vertical position for proper ventilation. The
cylinder must be provided with a shut-off
valve terminating in an LP/Propane gas
supply cylinder valve outlet specified. The
cylinder supply system must be arranged for
vapor withdrawal and provided with a listed
overfilling prevention device. If the appliance
is stored indoors the cylinder must be
disconnected and removed from the
appliance. Each tank is supplied with a dust
cap. Place dust cap on cylinder valve outlet
whenever the cylinder is not in use. Only
install the type of dust cap on the cylinder
valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result
in leakage of propane. The cylinder used
must include a collar to protect the cylinder
valve. Cylinders must be stored outdoors in a
well-vented area out of the reach of children.
vertical position for proper ventilation. The
cylinder must be provided with a shut-off
valve terminating in an LP/Propane gas
supply cylinder valve outlet specified. The
cylinder supply system must be arranged for
vapor withdrawal and provided with a listed
overfilling prevention device. If the appliance
is stored indoors the cylinder must be
disconnected and removed from the
appliance. Each tank is supplied with a dust
cap. Place dust cap on cylinder valve outlet
whenever the cylinder is not in use. Only
install the type of dust cap on the cylinder
valve outlet that is provided with the cylinder
valve. Other types of caps or plugs may result
in leakage of propane. The cylinder used
must include a collar to protect the cylinder
valve. Cylinders must be stored outdoors in a
well-vented area out of the reach of children.
BUILT-IN INSTALLATIONS
Built-in installations must be plumbed using a
fixed/hard line if the unit is going to be
operated at a distance exceeding 3 feet (0.91
meters) from the fuel supply per ANSI Z21.24
CSA. Also, in a built-in construction where an
LP/Propane tank is going to be used, there
MUST be some type of support (braces, cut-
out, etc.) to prevent tank from moving within
the installation. The support must also allow
the LP/Propane tank to withstand a horizontal
tipping force equal to the weight of the tank
without tipping over. The tank can not tip
over or deflect more than 1.00 inch when a 38
lb. horizontal force is applied to a 20 lb.
LP/Propane tank.
fixed/hard line if the unit is going to be
operated at a distance exceeding 3 feet (0.91
meters) from the fuel supply per ANSI Z21.24
CSA. Also, in a built-in construction where an
LP/Propane tank is going to be used, there
MUST be some type of support (braces, cut-
out, etc.) to prevent tank from moving within
the installation. The support must also allow
the LP/Propane tank to withstand a horizontal
tipping force equal to the weight of the tank
without tipping over. The tank can not tip
over or deflect more than 1.00 inch when a 38
lb. horizontal force is applied to a 20 lb.
LP/Propane tank.
LP/Propane Tank Requirements