TallyGenicom 3860 クイック設定ガイド
GEK-01054
12
Powering on the Printer
Power Cords
Do not use two-wire extension cords or adapters that allow connection to
ungrounded outlets.
ungrounded outlets.
A 6.5-foot power cord is shipped with the printer. The power cord
included with printers sold for 115V installations in the U.S. and Canada
is ready to use. International model printers are shipped with a power
cord for the destination country.
included with printers sold for 115V installations in the U.S. and Canada
is ready to use. International model printers are shipped with a power
cord for the destination country.
For units to be operated at 115V, use a UL Listed/CSA Certified three-
conductor cord set, #18 AWG minimum, Type SVT or SJT. The
maximum length is 15 feet. There must be a NEMA 5-15P (parallel
blade, grounding type) plug on one end and a CEE 22/5 socket on the
other end. The cord set should be rated 10A, 250V and have a
grounding plug with safety approvals appropriate for the country in which
the equipment will be installed.
conductor cord set, #18 AWG minimum, Type SVT or SJT. The
maximum length is 15 feet. There must be a NEMA 5-15P (parallel
blade, grounding type) plug on one end and a CEE 22/5 socket on the
other end. The cord set should be rated 10A, 250V and have a
grounding plug with safety approvals appropriate for the country in which
the equipment will be installed.
For units to be operated at 230V inside U.S. and Canada, use a UL
Listed/CSA Certified three-conductor cord set, #18 AWG minimum, Type
SVT or SJT. The maximum length is 15 feet. There must be a NEMA 6-
15P (tandem blade, grounding type) plug on one end and a CEE 22/5
socket on the other end. The cord set should be rated 10A, 250V and
have a grounding plug with safety approvals appropriate for the country
in which the equipment will be installed.
Listed/CSA Certified three-conductor cord set, #18 AWG minimum, Type
SVT or SJT. The maximum length is 15 feet. There must be a NEMA 6-
15P (tandem blade, grounding type) plug on one end and a CEE 22/5
socket on the other end. The cord set should be rated 10A, 250V and
have a grounding plug with safety approvals appropriate for the country
in which the equipment will be installed.
For units to be operated at 230V outside the U.S. and Canada, use a
three-conductor cord set, EUR-H05VV-FG31,0 minimum, with a CEE
22/5 socket on one end. The cord set should be rated 10A, 250V and
have a grounding plug with safety approvals appropriate for the country
in which the equipment will be installed. The cord set should be marked
HAR.
three-conductor cord set, EUR-H05VV-FG31,0 minimum, with a CEE
22/5 socket on one end. The cord set should be rated 10A, 250V and
have a grounding plug with safety approvals appropriate for the country
in which the equipment will be installed. The cord set should be marked
HAR.
Plug It In and Turn It On
Plug in the power cord.
Make sure the power switch is off. The power switch is on the back of
the printer. Press the switch down to be sure it is off. Plug the female
end of the cord to the power receptacle on the back of the printer under
the power switch. Plug the male end into an AC outlet.
the printer. Press the switch down to be sure it is off. Plug the female
end of the cord to the power receptacle on the back of the printer under
the power switch. Plug the male end into an AC outlet.
Turn on the power switch.
All four lights on the control panel come on for a few seconds. The print
head moves to its home position at the left side of the printer. All lights
go out. The fault light flashes on and off.
head moves to its home position at the left side of the printer. All lights
go out. The fault light flashes on and off.
The LCD should say Fault: Paper Out
The liquid crystal display on the front panel shows this message until
paper is loaded.
paper is loaded.
If the printer did not power on.
Check the AC outlet with another appliance.