KitchenAid 36" Convertible Island-Mount 400-CFM Glass Canopy Hood インストールガイド

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting 

installation. Read and follow the instructions provided 

with any tools listed here.

 

■

Level

 

■

Drill with 1

1

/

4

" (3.2 cm), 

3

/

8

" (9.5 mm), 

1

/

8

" (3.2 mm), 

and 

7

/

64

" (2.75 mm) drill bits

 

■

Pilot hole drill bits (determined by chimney support 

attachment method)

 

■

Pencil

 

■

Wire stripper or utility knife

 

■

Tape measure or ruler

 

■

Pliers

 

■

Caulking gun and weatherproof caulking compound

 

■

Vent clamps

 

■

Jigsaw or keyhole saw

 

■

Flat-blade screwdriver

 

■

Metal snips

 

■

Phillips screwdriver

 

■

Home power supply cable

 

■

1

/

2

" (12.7 mm) UL listed or CSA approved strain relief

 

■

3 UL listed wire connectors

 

■

1 wall or roof cap

 

■

Metal vent system

 

■

Recirculation Kit Part Number W10680067 for non-vented 

(recirculating) installations only. See “Assistance or Service” 

section to order.

 

■

6" (15.2 cm) diameter round metal vent duct - 

length required is determined by ceiling height.

Remove parts from packages. Check that all parts are included.

 

■

Hood ventilator assembly with canopy glass, retainer 

brackets, rubber seals, and light bulb installed.

 

■

Metal grease filter

 

■

60 - 4.2 x 8 mm screws

 

■

4 - 3.5 x 6.5 mm screws

 

■

4 - 5 x 45 mm screws

 

■

2 - 2.9 x 3 mm screws

 

■

T10 Torx

®†

 adapter

 

■

T20

®†

 Torx

®

 adapter

 

■

2 - Upper vent covers

 

■

2 - Lower vent covers

 

■

4 - Plastic vent clips

 

■

Mounting template

 

■

Upper horizontal support bracket

 

■

Horizontal support

 

■

8 - Vertical supports

 

■

Vent transition with back draft damper installed.

 

■

2 - 3.5 x 9.5 mm mounting screws

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the 

installer’s responsibility to comply with installation clearances 

specified on the model/serial/rating plate. The model/serial/

rating plate is located behind the left filter on the rear wall 

of the vent hood.
Canopy hood location should be away from strong draft areas, 

such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. 

Given dimensions provide minimum clearance.
Grounded electrical outlet is required. See “Electrical 

Requirements” section.
Because of the size and weight of this island hood, the chimney 

support must be securely attached to the ceiling.

 

■

For plaster or drywall ceilings, the chimney support must 

be attached to joists. If this is not possible, you must build 

a support structure behind the plaster or drywall. The 

support structure must be able to support 80 lbs (36.6 kg).

This range hood is recommended for use with cooktops 

with a maximum total rating of 60,000 BTUs or less.
The range hood is factory set for venting through the roof or wall.
For non-vented (recirculating) Installation see “Non-vented 

(recirculating) Installation” in “Install Range Hood” section. 

Recirculation Kit Part Number W10680067 is available from 

your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will 

be installed must be sealed.

The installation of this range hood must conform to the 

Manufactured Home Construction Safety Standards, Title 

24 CFR, Part 328 (formerly the Federal Standard for Mobile 

Home Construction and Safety, Title 24, HUD, Part 280) 

or when such standard is not applicable, the standard for 

Manufactured Home Installation 1982 (Manufactured Home 

Sites, Communities and Setups) ANSI A225.1/NFPA 501A, 

or latest edition, or with local codes.

†

®

TORX and T20 are registered trademarks of Acument Intellectual 

Properties, LLC.