Craftsman 54985 ユーザーズマニュアル
ASSEMBLY STEP 5
Tighten the Chain
Tighten the Chain
1. Spin the inner nut and lock washer down the trolley threaded
shaft, away from the trolley.
2. To tighten the chain, turn outer nut in the direction shown
(Figure 1).
3. When the chain is approximately 1/4" (6 mm) above the base
of the rail at its midpoint, re-tighten the inner nut to secure the
adjustment (Figure 2).
adjustment (Figure 2).
Sprocket noise can result if chain is too loose. When installation
is complete, you may notice some chain droop with the door
closed. This is normal. If the chain returns to the position shown
in Figure 2 when the door is open, do not re-adjust the chain.
is complete, you may notice some chain droop with the door
closed. This is normal. If the chain returns to the position shown
in Figure 2 when the door is open, do not re-adjust the chain.
NOTES:
l
During future maintenance, ALWAYS pull the emergency
release handle to disconnect trolley before adjusting chain.
release handle to disconnect trolley before adjusting chain.
l
You may notice loosening of chain after Adjustment Step 2
(Test the Safety Reversal System). Check for proper tension
and readjust chain if necessary. Then repeat Adjustment
Step 2.
(Test the Safety Reversal System). Check for proper tension
and readjust chain if necessary. Then repeat Adjustment
Step 2.
You have now finished assembling your garage door opener.
Please read the following warnings before proceeding to the
installation section.
Please read the following warnings before proceeding to the
installation section.
Figure 1
Figure 2
Base of Rail
Mid length of Rail
Chain
1/4" (6 mm)
Outer
Nut
Nut
Lock
Washer
Washer
Trolley
Threaded
Shaft
Threaded
Shaft
Inner Nut
To Tighten
Inner Nut
Inner Nut
To Tighten Outer Nut
INSTALLATION
IMPORTANT INSTALLATION INSTRUCTIONS
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND
INSTRUCTIONS.
2. Install garage door opener ONLY on properly balanced and
lubricated garage door. An improperly balanced door may
NOT reverse when required and could result in SEVERE
INJURY or DEATH.
NOT reverse when required and could result in SEVERE
INJURY or DEATH.
3. ALL repairs to cables, spring assemblies and other hardware
MUST be made by a trained door systems technician BEFORE
installing opener.
installing opener.
4. Disable ALL locks and remove ALL ropes connected to
garage door BEFORE installing opener to avoid
entanglement.
entanglement.
5. Install garage door opener 7 feet (2.1 m) or more above floor.
6. Mount the emergency release within reach, but at least
6. Mount the emergency release within reach, but at least
6 feet (1.83 m) above the floor and avoiding contact with
vehicles to avoid accidental release.
vehicles to avoid accidental release.
7. NEVER connect garage door opener to power source until
instructed to do so.
8. NEVER wear watches, rings or loose clothing while installing
or servicing opener. They could be caught in garage door or
opener mechanisms.
opener mechanisms.
9. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of children at minimum height of 5 feet
• out of reach of children at minimum height of 5 feet
(1.5 m).
• away from ALL moving parts of the door.
10. Place entrapment warning label on wall next to garage door
control.
11. Place manual release/safety reverse test label in plain view on
inside of garage door.
12. Upon completion of installation, test safety reversal system.
Door MUST reverse on contact with a 1-1/2" (3.8 cm) high
object (or a 2x4 laid flat) on the floor.
object (or a 2x4 laid flat) on the floor.
13. DO NOT enable the Timer-to-Close functionality if operating
either one-piece or swinging garage doors. To be enabled
ONLY when operating a sectional door.
ONLY when operating a sectional door.
11