Timberk SWH RE4 80 VH ユーザーズマニュアル
7
1. Power cord with a plug
2. Water heater
3. Check relief valve
4. Cold water supply valve*
5. Mixer*
6. Shower header*
7. Water main shut-off valve*
8. Pressure relieving opening
9. Water main
10. Bath tub*
11. T-bend*
12. Water outlet
13. Water inlet
NOTE:
If you install water heater of SWH RE4 ... VH series as vertical
direction, please mind the pipe of hot water is on the right.
direction, please mind the pipe of hot water is on the right.
Water heater mounting
NOTE:
Please, use accessories, provided by the manufacturer, to install the
water heater. Electric water heater must not be mounted on a wall prior
you make sure that the bracket is installed firmly and securely.
Otherwise the electric water heater may fall down from the wall, which
may cause its damage and even serious accidents involving bodily
injury. When determining points for bolt holes, it is necessary to
provision some spare space between the lower part of the water heater
and the floor not less than 0.6 m, and when installing RE4 VH
appliance horizontally there also must be some spare space between
the side cover on the right side and a wall to make it convenient to
perform maintenance if necessary.
water heater. Electric water heater must not be mounted on a wall prior
you make sure that the bracket is installed firmly and securely.
Otherwise the electric water heater may fall down from the wall, which
may cause its damage and even serious accidents involving bodily
injury. When determining points for bolt holes, it is necessary to
provision some spare space between the lower part of the water heater
and the floor not less than 0.6 m, and when installing RE4 VH
appliance horizontally there also must be some spare space between
the side cover on the right side and a wall to make it convenient to
perform maintenance if necessary.
Fig. 8
1. The electric water heater must be mounted on a solid wall. If wall
strength doesn't allow to bear the double weight of the total water
heater weight fully filled with water, then it should be mounted on a
special support.
2. After you chose the proper place to install the water heater,
determine points for holes for anchor hook bolts (to be determined in
accordance with the data sheet for the appliance you chose). Drill two
holes of the corresponding depth in the wall using a drill, dimensionally
fit for anchor bolts, enclosed with the water heater.
Then insert bolts into the drilled holes, and, turning bolt hooks
clockwise, securely tighten bolt nuts, then hang the water heater on
these anchor bolt hooks (see Fig. 8).
3. Fix a power outlet to the wall. Requirements to the outlet are as
follows: 220V/10A, single-phase, three-wired. It is recommended to
place the outlet on the right side above the water heater.
strength doesn't allow to bear the double weight of the total water
heater weight fully filled with water, then it should be mounted on a
special support.
2. After you chose the proper place to install the water heater,
determine points for holes for anchor hook bolts (to be determined in
accordance with the data sheet for the appliance you chose). Drill two
holes of the corresponding depth in the wall using a drill, dimensionally
fit for anchor bolts, enclosed with the water heater.
Then insert bolts into the drilled holes, and, turning bolt hooks
clockwise, securely tighten bolt nuts, then hang the water heater on
these anchor bolt hooks (see Fig. 8).
3. Fix a power outlet to the wall. Requirements to the outlet are as
follows: 220V/10A, single-phase, three-wired. It is recommended to
place the outlet on the right side above the water heater.
NOTE:
In places or on the wall, where water may get to, the power outlet
installation height must be not less than 1.8 m.
In places or on the wall, where water may get to, the power outlet
installation height must be not less than 1.8 m.
Connection to water main
1. The heater must be connected to water main with at least 0.1 MPa
pressure; maximum pressure is 0.75 MPa.
pressure; maximum pressure is 0.75 MPa.
ENGLISH
www.timberk.com electric storage water heater