Timberk SWH RE4 80 VH ユーザーズマニュアル
9
IMPORTANT!
To provide reliable operation and safe use of the water heater,
prior to the first run check if it is properly connected to the 220V
AC mains. The water heater to be connected must be securely
linked with the earth circuit of your electric mains. The
waterheater must be grounded properly, otherwise it is extremly
dangerous for life safety.
prior to the first run check if it is properly connected to the 220V
AC mains. The water heater to be connected must be securely
linked with the earth circuit of your electric mains. The
waterheater must be grounded properly, otherwise it is extremly
dangerous for life safety.
ENGLISH
7. WATER HEATER OPERATION
1. At first, open one of the separable taps at the water heater outlet,
then open the inlet tap. The electric water heater will start filling with
water. When water flows from separable tap freely, it means the water
heater is fully filled with water and you can close the separable tap.
then open the inlet tap. The electric water heater will start filling with
water. When water flows from separable tap freely, it means the water
heater is fully filled with water and you can close the separable tap.
NOTE:
During normal operation the cold water supply valve must be
opened.
During normal operation the cold water supply valve must be
opened.
2. Plug the power cord into the outlet
3. Turn the thermostate handle (fig. 4,5) clockwise and set the desirable
temperature. The temperature can be set from +35°C (±5° ) (MIN"
position of the thermostat knob) up to 70°C (±5° ) (rightmost "MAX"
position of the thermostat knob). To reduce the water temperature turn
the handle anticlockwise.
4. Water temperature keeps up by the thermostate automatically.
When water temperature reach the set level, Heating is automatically
switched off. At that, the indicator lamp in the lower part of the
appliance extinguishes. When the temperature wil be lower then set,
the heating will automaticlly start again and the indicator lamp lights
up.
5. To turn off the waterheater, turn the handle to the closest left position
« » and unplug the power cord or disconnect the appliance from the
power supply.
temperature. The temperature can be set from +35°C (±5° ) (MIN"
position of the thermostat knob) up to 70°C (±5° ) (rightmost "MAX"
position of the thermostat knob). To reduce the water temperature turn
the handle anticlockwise.
4. Water temperature keeps up by the thermostate automatically.
When water temperature reach the set level, Heating is automatically
switched off. At that, the indicator lamp in the lower part of the
appliance extinguishes. When the temperature wil be lower then set,
the heating will automaticlly start again and the indicator lamp lights
up.
5. To turn off the waterheater, turn the handle to the closest left position
« » and unplug the power cord or disconnect the appliance from the
power supply.
IMPORTANT!
The outlet must be designed for rated current not less than 10A,
electric cable with copper core must have cross section not less
than 3x1.5 mm2 (for copper).
The outlet must be designed for rated current not less than 10A,
electric cable with copper core must have cross section not less
than 3x1.5 mm2 (for copper).
IMPORTANT!
Optimum position on the control panel corresponds to the
optimum water heating temperature of 58 +/-2°C, at which:
1. The user is less likely to get burned in case when the outlet
water temperature is incorrectly adjusted.
2. A sufficient amount of hot water is obtained after mixing with
cold water, at a lesser power energy consumption.
3. Less scale is generated on the heating element and internal
surfaces of the water heater.
1. The user is less likely to get burned in case when the outlet
water temperature is incorrectly adjusted.
2. A sufficient amount of hot water is obtained after mixing with
cold water, at a lesser power energy consumption.
3. Less scale is generated on the heating element and internal
surfaces of the water heater.
ATTENTION!
Water can start to drip from the opening of safety valve then
heating process is going. It s impossible to avoid leakage of
water and you can t prevent this! Locking of valve may cause
rupture of the inner tank in case of failure.
Water can start to drip from the opening of safety valve then
heating process is going. It s impossible to avoid leakage of
water and you can t prevent this! Locking of valve may cause
rupture of the inner tank in case of failure.
www.timberk.com electric storage water heater