Cisco Cisco Prime Collaboration Assurance 11.5 白書
© 2014 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 34 of 40
Synthetic Test Description
Expected Results
Off-Hook
Simulates an off-hook state to Cisco
Unified Communications Manager/Cisco
Unified Communications Manager
Express and checks for receipt of a dial
tone
Unified Communications Manager/Cisco
Unified Communications Manager
Express and checks for receipt of a dial
tone
Receives a dial-tone signal from Cisco Unified Communications Manager. The
registration of the synthetic phone takes place only for the first time because
registration is a costly operation on Cisco Unified Communications Manager.
registration of the synthetic phone takes place only for the first time because
registration is a costly operation on Cisco Unified Communications Manager.
However, if the test fails, then synthetic phones are registered again for the next test
cycle only.
cycle only.
After the synthetic phone is registered, Cisco Prime Collaboration Assurance checks
for a dial-tone signal from Cisco Unified Communications Manager.
for a dial-tone signal from Cisco Unified Communications Manager.
End-to-End
Call
Call
Initiates a call to a second simulated or
real IP phone
real IP phone
Registers, goes off-hook, and places the call.
Ring indication.
Destination phone goes off-hook to accept the call.
If call progress tones and announcements are configured on the gateway for your
end-to-end call, the test may succeed even before the phone rings or after a couple
of rings.
end-to-end call, the test may succeed even before the phone rings or after a couple
of rings.
This indicates that your gateway is working correctly. It can also confirm that the
destination route pattern is correct.
destination route pattern is correct.
The registration of the phone occurs only during the first test because registration is
a costly operation on Cisco Unified Communications Manager/Cisco Unified
Communications Manager Express. However, if the test fails, the registration will
occur for the next test cycle only.
a costly operation on Cisco Unified Communications Manager/Cisco Unified
Communications Manager Express. However, if the test fails, the registration will
occur for the next test cycle only.
Enable RTP transmission: Cisco Prime Collaboration Assurance plays a recorded
announcement upon answer. Use this feature in conjunction with the Cisco 1040
Sensor to monitor the quality of voice (QoV) of the test call.
announcement upon answer. Use this feature in conjunction with the Cisco 1040
Sensor to monitor the quality of voice (QoV) of the test call.
TFTP Receive
Test
Test
Performs a TFTP get-file operation on
the TFTP server
the TFTP server
Successful download of a configuration file from the TFTP server.
Emergency
Call Test
Call Test
Initiates a call to the emergency number
to test the dynamic routing of emergency
calls
to test the dynamic routing of emergency
calls
All calls initiated.
Ring indication on Public Safety Answering Point (PSAP) and On Site Alert Number
(OSAN), if configured.
(OSAN), if configured.
Cisco
Conference
Connection
Test
Conference
Connection
Test
Creates a conference (meeting) in the
Conference Center and connects to the
meeting
Conference Center and connects to the
meeting
Conference created with the specified meeting ID.
Call initiated.
First person and second person (if configured) successfully connect to the
conference.
conference.
Cisco Unity
Message
Waiting
Indicator Test
Message
Waiting
Indicator Test
Calls the target phone and leaves a voice
message in the voice mailbox
message in the voice mailbox
Activation of the phone’s message-waiting indicator. The message is then deleted
and the message-waiting indicator is deactivated.
and the message-waiting indicator is deactivated.
How Many Simulated IP Phones Do I Need?
The number of simulated IP phones you need to define in Cisco Unified Communications Manager/Cisco Unified
Communications Manager Express depends on the number of tests you plan to configure. Different types of
confidence tests need a different number of IP phones. See Table 4.
A predefined MAC address range has been set aside for these IP phones so that it does not clash with any of the
real IP phones or devices in the network. The MAC address range that is available for synthetic testing is between
00059a3b7700 and 00059a3b8aff.
It is recommended that you input the description for these IP phones as Cisco Prime Collaboration Assurance
Simulated Phone when they are configured in Cisco Unified Communications Manager/Cisco Unified
Communications Manager Express so that the description is distinct from the descriptions of other IP phones in
Cisco Unified Communications Manager/Cisco Unified Communications Manager Express. The phones to be used
in confidence testing must be configured as 7960 phones in Cisco Unified Communications Manager/Cisco Unified
Communications Manager Express.