Samsung SNC-C6225P ユーザーズマニュアル
66 – 10x Network Mini Smart Dome Camera
setup tool
To set a motion detection target area
You can set a specifi c area to detect a motion in.
1) In the MOTION window, click the [Motion Area]
button.
- The Motion Area window appears.
- You can set a specifi c area to detect a motion in.
- The Motion Area window appears.
- You can set a specifi c area to detect a motion in.
2) Click over square boxes corresponding to your
desired motion detection target area.
- The selected area is colored in yellow.
- The selected area is colored in yellow.
3) To cancel a selection, click over the square box
once again.
- The square box returns to its original color.
- The square box returns to its original color.
4) Click the [Apply] button of Motion Area window.
5) To complete the setting, click the [Apply] button of
Motion Setup.
- If you don't click the [Apply] button of Motion
- If you don't click the [Apply] button of Motion
Setup, Motion Area isn't saved.
- The motions in the selected area will be detected.
SCHEDULE
You can have a JPEG image sent through FTP and Email
periodically.
periodically.
Schedule Transfer Function
<Enable> activates the scheduled transmission
function, while <Disable> disables the function.
function, while <Disable> disables the function.
❖
•
Transfer Interval
You can set the time interval to transmit images.
You can select a unit of time from <Seconds> or
<Minutes>.
You can set the time interval so that an image
is transmitted every 5/15/30/45/60 seconds or
minutes.
You can select a unit of time from <Seconds> or
<Minutes>.
You can set the time interval so that an image
is transmitted every 5/15/30/45/60 seconds or
minutes.
Activation Time
You can set the time to execute the scheduled
transmission function.
<Always>: Always transmits images according to
the specifi ed interval.
<Only Scheduled Time>: Transmits images
according to the specifi ed interval during the
specifi ed time period on the specifi ed day of the
week.
transmission function.
<Always>: Always transmits images according to
the specifi ed interval.
<Only Scheduled Time>: Transmits images
according to the specifi ed interval during the
specifi ed time period on the specifi ed day of the
week.
The Start Time must be prior to and must differ from
the End Time.
the End Time.
STREAMING SETUP
You can control the data transfer rate according to the
camera video streaming type and network bandwidth.
camera video streaming type and network bandwidth.
Streaming Protocol
You can select a protocol for video transmission
from the <TCP>, <UDP(Unicast)> and
<UDP(Multicast)>.
<TCP>: It is a general purpose protocol used
for a transmission that requires reliability. Since
it provides a connection based communication
between the sender and recipient, it provides high
reliability against transmission data loss. However, it
is inappropriate to transmit a large amount of data
in real-time because of its transmission overhead.
It enables reliable data transmission over xDSL and
cable network at a relatively slow speed.
<UDP(Unicast)>: It refers to transmitting data to
only one receiver (1:1).
<UDP(Multicast)>: It refers to the data transfer
protocol in one-to-many (1:N) between the
transmitting and receiving terminals. Although it
alleviates the network load, it requires <Multicast>
router. For more information such as whether
the network over which the camera is installed
supports <Multicast>, ask your network
administrator.
from the <TCP>, <UDP(Unicast)> and
<UDP(Multicast)>.
<TCP>: It is a general purpose protocol used
for a transmission that requires reliability. Since
it provides a connection based communication
between the sender and recipient, it provides high
reliability against transmission data loss. However, it
is inappropriate to transmit a large amount of data
in real-time because of its transmission overhead.
It enables reliable data transmission over xDSL and
cable network at a relatively slow speed.
<UDP(Unicast)>: It refers to transmitting data to
only one receiver (1:1).
<UDP(Multicast)>: It refers to the data transfer
protocol in one-to-many (1:N) between the
transmitting and receiving terminals. Although it
alleviates the network load, it requires <Multicast>
router. For more information such as whether
the network over which the camera is installed
supports <Multicast>, ask your network
administrator.
❖
•
❖
•
M
❖
•