Canon ir2016, ir2020 マニュアル

3

Chapter 2  Standards and 

Adjustments

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

After replacing the contact image sensor (CIS), go through the following

steps to perform inter-channel output correction:

1) Enter the service mode.
Sequentially press the User Mode key "

", 2 key, 8 key, and User Mode

key "

" on the operation panel.

2) Using the arrow keys on the operation panel, display "TEST MODE".

3) Press the OK key. 

4) Press the 2 key. "SCAN TEST" appears.

5) Press the 1 key.

After completion of the above steps, contact sensor output correction will be

performed and parameters will be set automatically.

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

After replacing the developing assembly, go through the following steps

in the developing assembly idle rotation mode before installing the toner car-

tridge.

1) Plug the power cord into the outlet.

2) Open the front cover.

3) With the front cover open, turn on the main power switch.

4) When a message appears on the operation panel display, press the

following keys to enter the service mode:

Additional Functions key > 2 key > 8 key > Additional Functions key

5) Select "#PRINT" using the + or - key, and then press the OK key. 

6) Select "#PRINT SW" using the + or - key, and hen press the OK key.

Confirm that the following message is displayed:

Message: #PRINT SW 001 00000000

7) Press the following keys and confirm the message:

# key > 1 key > 1 key

Message: #PRINT SW 011 00000000

8) Position the cursor to Bit-1 (second from right) using the + or - key, and

press the 1 key, and then confirm the following message:  

Message: #PRINT SW 011 00000010

9) Press the OK key. Confirm that "SW 011" changes to "SW 012".

Message: #PRINT SW 012 00000000

10) Press the Reset key to exit the service mode.

11) Close the front cover. The machine will run in the developer idling mode

for about 1 minute.

12) When the machine stops, the idling mode ends.

Install, the toner cartridge following the above-mentioned procedure.

iR2016J / iR2016 / iR2020 /  / iR2016i / iR2020i

After replacing the image processor PCB with a new one, input the all value

printed on the service label affixed to the rear cover.

Make the following adjustments:

- Correction of output between CIS channels 

1) Enter the service mode.
Sequentially press the User Mode key "

", 2 key, 8 key, and User Mode

key "

" on the operation panel.

2) Using the arrow keys on the operation panel, display "TEST MODE".

3) Press the OK key. 

4) Press the 2 key. "SCAN TEST" appears.

5) Press the 1 key.

After completion of the above steps, contact sensor output correction will be

performed and parameters will be set automatically.

- Read position adjustment (Stream reading: Only when the ADF is installed)

1) Enter the service mode.
Press the User Mode key "

", 2 key, 8 key, User Mode key "

" on the

operation panel of the host machine. 

2) Using the arrow keys on the operation panel, display "TEST MODE".

3) Press the OK key.

4) Press the 2 key. "SCAN TEST" appears.

5) Press the 3 key. "SHEET POS ADJ" appears.

The optical system starts scanning. Several seconds later, automatic adjust-

ment of the reading position finishes and "OK" appears.

If automatic adjustment fails, "NG" appears. Perform the following pro-

cedure:

Clean the white roller of the DADF and the document glass of the host ma-

chine, and then retry auto adjustment.