Extron electronic DSC 3G-HD A ユーザーズマニュアル
DSC 3G-HD A • Setup Guide (Continued)
2
Front Panel Overview
DSC 3G-HD A
Extron
CONFIG
INPUT RATE
MENU
AUTO-
IMAGE
IMAGE
ENTER
OUTPUT
UNKNOWN
SYNC
HDTV
PC
AUDIO
HOLD
FOR XGA
720 P
2.97 Gbps
1.485 Gbps
270 Mbps
3
4
5
6
1
2
a
Status LED — Lights steadily amber when there is power but no signal, blinks amber every 3 seconds when the unit is in
standby mode, and lights steadily green when both power and an input signal are present.
b
USB configuration port — Connect a control system or computer to this mini USB port (cable not supplied) for device
configuration, control, and firmware upgrading.
c
Input Rate LEDs — One signal LED (2.97 Gbps, 1.485 Gbps, or 270 Mbps) lights to indicate the type of signal that is
present. The Unknown LED lights if the signal does not reference SMPTE 259M, 292M, or 424M.
d
Output LEDs — Light to indicate the presence of sync and other output signal information:
z
HDTV: Indicates 2k, 1080p, 1080i, 720p, 480p, 576p, or custom rates.
z
PC: Indicates VESA standard or custom computer rates.
z
Audio: Audio is embedded in the signal.
z
Sync: Sync is present (does not light if video sync is muted).
e
Menu and Enter buttons — Let you access the OSD and select submenus and options from the menus.
f
Navigation buttons — Press these right , left , up
, and down
arrow buttons to step through the OSD submenus,
to lock the front panel (see the next section), perform Auto-Image (press ), and reset the output rate (hold
for 5 seconds).
Locking the Front Panel (Executive Mode)
To prevent unauthorized access or accidental changes to DSC settings, you can lock the front panel controls, making control
available only by SIS commands. (The default state is unlocked.) You can lock and unlock the front panel as follows:
available only by SIS commands. (The default state is unlocked.) You can lock and unlock the front panel as follows:
z
Using the front panel buttons: To lock, press the Menu and
buttons simultaneously and hold them until the OSD
displays
Executive Mode Enabled (approximately 5 seconds). To unlock, repeat this process.
z
SIS commands: To lock (enable executive mode), enter
1X. To unlock (disable executive mode), enter 0X.
Configuring the DSC 3G-HD A
The DSC 3G-HD A can be configured through a host connected
to the RS-232 or USB port, using Extron PCS Windows-based
control software (available at no charge at
to the RS-232 or USB port, using Extron PCS Windows-based
control software (available at no charge at
). You
can also configure it using the OSD menu system, described below.
On-Screen Display (OSD) Menu System
The OSD menu system consists of seven submenus and two
information screens. To access the menus, press the front panel
Menu button. With the main menu displayed, use the arrow buttons
to step through the submenus and submenu options. Press the
Enter button to select items that you highlight. Communication and
Device Info screens are read-only and do not provide selections.
information screens. To access the menus, press the front panel
Menu button. With the main menu displayed, use the arrow buttons
to step through the submenus and submenu options. Press the
Enter button to select items that you highlight. Communication and
Device Info screens are read-only and do not provide selections.
•
Quick Setup
•
User Presets
•
Picture Controls
•
Input
•
Output
•
Audio
•
Advanced
•
Communication
•
Device Info.
NOTE:
The OSD times out and closes after 1 minute if no
buttons are pressed.