Philips vr210 ユーザーズマニュアル

Press 

START + 

or

 –

(Number button 

1

 or 

4

).

• Each time you press

the button, the set
time changes by 1-
minute intervals. If you hold the button,
the set time changes by 30-minute
intervals.

Press 

STOP + 

or

 –

(Number button 

2

 or

5

).

• Each time you press

the button, the set
time changes by 1 minute intervals. If you
hold the button, the set time changes by
30-minute intervals.

Press 

ALT/SPEED

.

• Each time you press

the button, the tape
speed alternates
between “SP”, “LP”
and “SLP.”
SP, LP : For PAL signal
SP, SLP : For NTSC signal

Press 

DATE + 

or

 –

(Number button 

3

 or 

6

).

• The year and day of

the week is displayed
automatically.

Press 

OK/STATUS

 or 

TIMER

.

“PROGRAM WAS COMPLETED”
appears on the TV screen.
After 5 seconds, the above message
disappears, and the normal TV picture
resumes. The

(Timer) indicator

lights up on the display.

• If “PROGRAM NOT COMPLETED”

appears, try again from step 1.

• If “PROGRAM OVERLAPPED”

appears, the timer recording you just
programmed overlaps another timer
recording. The Program Review screen
will appear with a magenta line blinking.
To change any item on the overlapping
programs, see page 17.

If you want to store other
programmes, repeat steps 1 to 8.

Press 

POWER

 to turn off the VCR.

The VCR must be turned off for a timer
recording to take place. If you forget to
turn off the VCR, “PLEASE TURN
OFF VCR FOR TIMER
RECORDING” flashes on your TV
screen two minutes before a timer
recording starts. To remove the
message, press the 

CLEAR

 button.

If you want to record the same
programme daily, press 

DAILY

(Number button 8) during step 3
through 7. ( Press the button again to
cancel)
The VCR will record a TV programme
every day (Monday through Friday) at
the same time and length (Daily
Recording).

If you want to record the same
programme weekly, press 

WEEKLY

(Number button 9) during step 3
through 7. ( Press the button again to
cancel)
The VCR will record a TV programme
once a week at the same day, time and
length (Weekly Recording).

Press 

POWER

 to turn on the VCR.

You can operate your VCR normally.

Press 

POWER

.

Recording stops and the VCR turns off.
If it is a Daily or Weekly Recording,
future recordings will be carried out as
programmed.

ONE TIME PROGRAM
   PROGRAM     1
   CHANNEL+/–   
   START +/–      20 : 00  
   STOP +/–        – –:– –  
   REC SPEED   SP
   DATE +/–        – –/– –/– –
                          
DAILY: 8                   WEEKLY: 9
CONFIRM: OK       END: TIMER 

12    

ONE TIME PROGRAM
   PROGRAM     1
   CHANNEL+/–   
   START +/–      20 : 00 
   STOP +/–        21 : 00   
   REC SPEED   SP
   DATE +/–        – –/– –/– –
                          
DAILY: 8                   WEEKLY: 9
CONFIRM: OK       END: TIMER 

12    

ONE TIME PROGRAM
   PROGRAM     1
   CHANNEL+/–   
   START +/–      20 : 00 
   STOP +/–        21 : 00 
   REC SPEED   LP
   DATE +/–        – –/– –/– –
                           
DAILY: 8                   WEEKLY: 9
CONFIRM: OK       END: TIMER 

12    

ONE TIME PROGRAM
   PROGRAM     1
   CHANNEL+/–   
   START +/–      20 : 00   
   STOP +/–        21 : 00   
   REC SPEED   LP
   DATE +/–        14/07/00
                          FRIDAY
DAILY: 8                   WEEKLY: 9
CONFIRM: OK       END: TIMER         

12    

This function allows you to set the
timer recording program without going
through the regular set up with the on
screen. The extent of programming is
24 hours from the current time.

1 Insert a tape into the VCR and press

the  “TURBO TIMER”  button on
the remote control. Current time will
appear on the display panel.

2 To change the START time, press the

PLAY

 

5 or 

STOP

 

∞ ( if you press

and hold the button, the time changes
in 30-minute increments) then press

OK/STATUS.

3 To change the STOP time, press the

PLAY

 

5 or 

STOP

 

∞ ( if you press

and hold a button, the time changes
in 30-minute increments) then press

OK/STATUS.

4 To change the CHANNEL number,

press the 

PLAY

 

5 or 

STOP

 

∞, then

press 

OK/STATUS.

5 The data input will be memorized

and the Turbo Timer mode will be
finished so that normal display
appears.

6 Turn off the VCR.

Notes:

• To exit Turbo Timer mode at any step,

press the TURBO TIMER button.

• If “Err” appears on the display panel,

all eight programs have been set and
Turbo Timer will not proceed. To
remove the error message, press the
TURBO TIMER button again.

• Settings of Turbo Timer will appear

on the display panel only and not on
the screen.

• Programs Overlap Warning does not

function with Turbo Timer.

• DAILY or WEEKLY programming

are not available on Turbo Timer.

• Tape speed can be selected anytime

during steps 2 through 4.

vr210/410/55

00.3.6, 1:10 PM

16