Philips vr210 ユーザーズマニュアル
— 15 —
• Once the cassette is ejected, the DSPC data
is cancelled. The next time the cassette is
used for recording, DSPC is re-performed.
used for recording, DSPC is re-performed.
• When “DSPC” is displayed, the VCR does
not start One Touch Recording (✈P. 14).
• Since the DSPC system works before
recording actually starts, there is a delay
of approximately 7 seconds after
of approximately 7 seconds after
REC/
OTR
¶ is pressed. To make sure you
record the desired scene or programme in
its entirety, first perform the following
steps:
1) Press and hold STILL/SLOW (or
its entirety, first perform the following
steps:
1) Press and hold STILL/SLOW (or
STILL/PAUSE
8 on the front panel)
and press REC/OTR
¶ to engage the
RECORD PAUSE mode.
•
The VCR then automatically checks the
condition of the tape and, after
approximately 7 seconds, re-enters
RECORD PAUSE.
condition of the tape and, after
approximately 7 seconds, re-enters
RECORD PAUSE.
2) Press REC/OTR
¶ again to start
recording.
•
If you want to by pass the DSPC
system and begin recording immedi-
ately, set “DSPC” to “OFF”.
system and begin recording immedi-
ately, set “DSPC” to “OFF”.
For Playback
Press
PLAY
3.
• The VCR adjusts the playback picture qual-
ity based on the quality of the tape in use.
• DSPC is active during Auto Tracking.
“DSPC” appears blinking on the front
panel’s display window.
panel’s display window.
Notes:
• When watching a tape recorded with
“DSPC” set to “ON”, it is recommended
that you leave DSPC to “ON” during
playback as well.
that you leave DSPC to “ON” during
playback as well.
• “DSPC” only appears at the beginning of
automatic tracking. Even though it doesn't
appear after that, the DSPC function is
operative.
appear after that, the DSPC function is
operative.
DSPC
The DSPC (Digital Studio Picture
Control) system checks the condition
of the tape in use during recording and
playback, and compensates to provide
the highest possible recording and
playback pictures. The default setting
is “ON”.
Control) system checks the condition
of the tape in use during recording and
playback, and compensates to provide
the highest possible recording and
playback pictures. The default setting
is “ON”.
1
Select VCR Set Up Mode
1 Press
VCR
.
2 Press
MENU
.
3 Press
PLAY
5 or
STOP
∞ to select
“VCR SET UP”
then press
then press
OK
/STATUS.
The VCR Set up menu appears.
2
Set DSPC Mode
Press PLAY
5 or STOP ∞ to select “
DSPC”, then press
FF
3 to set DSPC
to “ON” or “OFF”.
3
Finish Setting
Press
MENU
.
Once the “DSPC” mode is set to “ON”,
the DSPC system works for both
recording & playback, as described
below;
the DSPC system works for both
recording & playback, as described
below;
For Recording
Press
REC/OTR
¶.
DURING DSPC
DSPC COMPLETED
• The VCR spends approximately 7 seconds
assessing the condition of the tape, then
begins recording.
begins recording.
Notes:
• The DSPC system works for SP, LP or SLP
modes only after a tape has been inserted
and the Record mode is first initiated.
Also, it works if the colour mode is changed.
It does not work during recording.
and the Record mode is first initiated.
Also, it works if the colour mode is changed.
It does not work during recording.
• In the case of timer recording, the DSPC
system works before recording is initiated.
DSPC
ON
ON SCREEN MODE ON
TIMER REC SPEED MANUAL
TIMER REC SPEED MANUAL
SELECT: CHANGE:
END: MENU
END: MENU
Timer Recording
To record while you’re away, follow step
1 — 9 below. For each programme you
set, the VCR will turn on, start recording,
and turn off automatically. You can store
up to 8 programmes.
1 — 9 below. For each programme you
set, the VCR will turn on, start recording,
and turn off automatically. You can store
up to 8 programmes.
Make sure....
• The clock is set to the correct time
• The clock is set to the correct time
before setting timer recording.
• A cassette is inserted in the VCR and
the record tab of the cassette must
not be removed.
not be removed.
• The remote control operation mode
is set correctly for operating your
target component.
– Press
target component.
– Press
VCR
to operate the VCR.
– Press
TV
to operate the TV.
FOR EACH STEP BELOW, YOU
NEED TO FINISH WITHIN 60
SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO
BE RESTARTED FROM STEP 1.
NEED TO FINISH WITHIN 60
SECONDS; OTHERWISE,
PROGRAMMING WILL HAVE TO
BE RESTARTED FROM STEP 1.
1
Select Timer Mode
1 Press
VCR
.
2 Press
TIMER
.
The Timer
Recording menu
appears.
Recording menu
appears.
2
Select Programme mode
1 Press
PLAY
5 or
STOP
∞ to select
“QUICK PROG-
RAMMING” then
press
RAMMING” then
press
OK/STAT-
US
.
The Quick Programming menu
appears.
appears.
• If you have already made 8
programmes, “ALL PROGRAMS IN
USE” appears and goes back to the
Timer Recording menu. If this
happens, delete unwanted programmes.
(✈P.20)
USE” appears and goes back to the
Timer Recording menu. If this
happens, delete unwanted programmes.
(✈P.20)
3
Select Channel
Press
CH
5 or ∞ to
enter the TV channel.
• Holding down
CH
5
or
∞ rapidly scans
through the channels.
• To record from exter-
nal line input, press
CH
5 or ∞
until
“A/V REAR” or “A/V FRONT” appears.
ONE TIME PROGRAM
PROGRAM 1
CHANNEL+/–
START +/– – –:– –
STOP +/– – –:– –
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
PROGRAM 1
CHANNEL+/–
START +/– – –:– –
STOP +/– – –:– –
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
– –
ONE TIME PROGRAM
PROGRAM 1
CHANNEL+/– 12
START +/– – –:– –
STOP +/– – –:– –
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
PROGRAM 1
CHANNEL+/– 12
START +/– – –:– –
STOP +/– – –:– –
REC SPEED SP
DATE +/– – –/– –/– –
DAILY: 8 WEEKLY: 9
CONFIRM: OK END: TIMER
QUICK PROGRAMMING
PROGRAM REVIEW
PROGRAM REVIEW
SELECT: CONFIRM: OK
END: TIMER
END: TIMER
vr210/410/55
00.3.6, 1:09 PM
15