Crestron clw-dim1 dims1 slvd1 ユーザーズマニュアル

 

CLW-DIM1, DIMS1, & SLVD1(W/A/B) 

Following are specifications for the -DIM1, -DIMS1, and  
-SLVD1. 

The CLW-DIM1 (-DIM1) is a stand-alone wall box 
dimmer that can also act as a Cresnet

®

 device that reports 

to a Crestron

®

 control processor. The CLW-DIM1 has 

two preset lighting levels that can be adjusted (refer to 
note below). The CLW-DIM1 also includes two isolated, 
non-polarized Cresnet wires (plus a ground wire) for 
connecting to the Cresnet network over a twisted pair 
wire with shield.  

Power Requirements 

Line Power, 120 VAC, 60 Hz 

Default Net ID 

-DIM1: 80 
-DIMS1: 81 

Switch Type 

Dimmer 

Load Type 

Incandescent, Tungsten-Halogen, 
Magnetic Low Voltage 

2-Series Control System 
Update File

1,2

 

Version 3.117 or later 

Load Ratings

3

 

 

 Incandescent/Tungsten 

Halogen 

-DIM1: 1000W 
-DIMS1: 1000W 
-SLVD1: N/A 

  Magnetic Low Voltage

4

 

-DIM1: 1000VA/750W 
-DIMS1: 1000VA/750W 
-SLVD1: N/A 

Operating Temperature 
and Humidity 

32°F to 104°F (0°C to 40°C) 
10 to 90% Relative Humidity 
(Non-Condensing) 

Dimensions and Weight 

-DIM1 and -DIMS1: 
  Height: 4.13 in (10.48 cm) 
  Width: 2.38 in (6.03 cm) 
  Depth: 1.91 in (4.85 cm) 
  Weight: 4.9 oz (0.67 kg) 
-SLVD1: 
  Height: 4.13 in (10.48 cm) 
  Width: 1.75 in (4.45 cm) 
  Depth: 1.91 in (4.85 cm) 
  Weight: 3.6 oz (0.50 kg) 

NOTE:  The two preset levels are noted as Preset 1-High 
and Preset 1- Low. “Preset 1-High” is usually used for 
turning lights on to full brightness while preset “Preset 1-
Low” is usually used for turning the lights off. Although 
“Preset 1-High” and “Preset 1-Low” are usually used for 
“On” and “Off” respectively, the light level for each 
preset can be customized by the user. Refer to 
“Operation” on page 6 for more information on 
customizing light levels. 

The CLW-DIM1 features a three-position mode selection 
switch. Refer to “Operation” on page 6 for more 
information. In the absence of Cresnet communications, 
the dimmer can still be used to control lighting. 

The CLW-DIMS1 (-DIMS1) is similar to the -DIM1 with 
the added capability of working with a slave unit  
(CLW-SLVD1) in a multi-dimmer / single circuit 
application. 

The CLW-SLVD1 (-SLVD1) is a slave unit that when 
used in conjunction with the -DIMS1 acts as an additional 
dimmer control point in a multi-dimmer / single circuit 
application. It does not connect to a Cresnet system and 
cannot be used without a -DIMS1. The -SLVD1 does not 
have a mode selection switch and is not programmable. It 
emulates the operation of the -DIMS1 to which it is 
connected unless the mode selection switch of the master 
is set to “OFF”. 

1. 

The latest software versions can be obtained from the Crestron 
website. Refer to the NOTE following these footnotes. 

2. 

Crestron 2-Series control systems include the AV2 and PRO2. 
Consult the latest Crestron Product Catalog for a complete list of 
2-Series control systems. 

3. 

Refer to Derating Charts for Multigang Installations on page 4. 

4. 

VA ratings are for input power to the transformer. If you do not 
know the input power requirement of the transformer, use the 
bulb’s wattage rating to determine proper rating. 

These dimmers are available in white, almond, and black. 
White units are designated by part numbers ending in 
“W”. Almond units are designated by part numbers 
ending in “A”. Black units are designated by part numbers 
ending in “B”. Each dimmer can be covered with a 
decorative faceplate (not supplied). 

NOTE:  Crestron software and any files on the website 
are for Authorized Crestron dealers and Crestron 
Authorized Independent Programmers (CAIP) only. New 
users may be required to register to obtain access to 
certain areas of the site (including the FTP site). 

 

 

15 Volvo Drive   Rockleigh, NJ 07647

   

Tel: 888.CRESTRON

 

Fax: 201.767.7576

Specifications subject to 

www.crestron.com

change without notice.