Vertex Standard FT-2000 ユーザーズマニュアル
Page 125
FT-2000 O
PERATING
M
ANUAL
M
ENU
M
ODE
135 tAUd PE2 FRQ
Function: Selects the center frequency of the middle range
for the parametric microphone equalizer when the speech
processor is activated.
Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting: 800 Hz
for the parametric microphone equalizer when the speech
processor is activated.
Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting: 800 Hz
OFF:
The equalizer gain and Q-factor are set
to factory defaults (flat).
to factory defaults (flat).
700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz.
You may adjust the equalizer gain and
Q-factor at this selected audio frequency
via menu items “136 tAUd PE2 LVL”
and “137 PE2 BW.”
Q-factor at this selected audio frequency
via menu items “136 tAUd PE2 LVL”
and “137 PE2 BW.”
136 tAUd PE2 LVL
Function: Adjusts the equalizer gain of the middle range
of the parametric microphone equalizer when the speech
processor is activated.
Available Values: –10 ~ +10
Default Setting: –3
of the parametric microphone equalizer when the speech
processor is activated.
Available Values: –10 ~ +10
Default Setting: –3
137 tAUd PE2 BW
Function: Adjusts the Q-factor of the middle range of the
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values: 1 ~ 10
Default Setting: 1
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values: 1 ~ 10
Default Setting: 1
138 tUAd PE3 FRQ
Function: Selects the center frequency of the high range
for the parametric microphone equalizer when the speech
processor is activated.
Available Values: OFF/1500 ~ 3200 Hz (100 Hz/step)
Default Setting: 2100 Hz
for the parametric microphone equalizer when the speech
processor is activated.
Available Values: OFF/1500 ~ 3200 Hz (100 Hz/step)
Default Setting: 2100 Hz
OFF:
The equalizer gain and Q-factor are set
to factory defaults (flat).
to factory defaults (flat).
1500 ~ 3200: Center frequencies of 1500 Hz ~ 3200 Hz.
You may adjust the equalizer gain and
Q-factor in this selected audio fre-
quency via menu items “139 tUAd PE3
LVL” and “140 tUAd PE3 BW.”
Q-factor in this selected audio fre-
quency via menu items “139 tUAd PE3
LVL” and “140 tUAd PE3 BW.”
139 tUAd PE3 LVL
Function: Adjusts the equalizer gain of the high range of
the parametric microphone equalizer when the speech pro-
cessor is activated.
Available Values: –10 ~ +10
Default Setting: +6
the parametric microphone equalizer when the speech pro-
cessor is activated.
Available Values: –10 ~ +10
Default Setting: +6
140 tUAd PE3 BW
Function: Adjusts the Q-factor of the high range of the
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values: 1 ~ 10
Default Setting: 1
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values: 1 ~ 10
Default Setting: 1
TX GNRL G
ROUP
141 tGEn BIAS
This Menu item does not work. Please do not change
this setting.
this setting.
142 tGEn MAX PWR
Function: Selects a maximum output power limit.
Available Values: 10/20/50/100 W
Default Setting: 100 W
Available Values: 10/20/50/100 W
Default Setting: 100 W
143 tGEn PWRCTRL
Function: Configures the [RF PWR] knob.
Available Values: ALL/CAr
Default Setting: ALL
Available Values: ALL/CAr
Default Setting: ALL
ALL:The [RF PWR] knob is enabled on all modes.
CAr: The [RF PWR] knob is enabled in all modes
CAr: The [RF PWR] knob is enabled in all modes
except SSB. In this configuration, the SSB out-
put power will be set to maximum, regardless
of the [RF PWR] knob’s position.
put power will be set to maximum, regardless
of the [RF PWR] knob’s position.
144 tGEn ETX-GND
Function: Enables/Disables the TX GND jack on the rear
panel.
Available Values: EnA(ENABLE)/diS(DISABLE)
Default Setting: diS(DISABLE)
panel.
Available Values: EnA(ENABLE)/diS(DISABLE)
Default Setting: diS(DISABLE)
145 tGEn TUN PWR
Function: Selects a maximum output power limit for driv-
ing the input circuit of an external linear RF amplifier
while tuning (while using the Remote Control function
of the linear RF amplifier).
Available Values: 10/20/50/100 W
Default Setting: 100 W
ing the input circuit of an external linear RF amplifier
while tuning (while using the Remote Control function
of the linear RF amplifier).
Available Values: 10/20/50/100 W
Default Setting: 100 W
146 tGEn VOX SEL
Function: Selects the audio input source for triggering
TX during VOX operation.
Available Values: nic/dAtA
Default Setting: nic
TX during VOX operation.
Available Values: nic/dAtA
Default Setting: nic
nic(MIC):
The VOX function will be activated by
microphone audio input.
microphone audio input.
dAtA(DATA):
The VOX function will be activated
by data audio input.
147 tGEn EMRGNCY
Function: Enables Tx/Rx operation on the Alaska Emer-
gency Channel, 5167.5 kHz.
Available Values: EnA(ENABLE)/diS(DISABLE)
Default Setting: diS(DISABLE)
When this Menu Item is set to “EnA(ENABLE),” the spot
frequency of 5167.5 kHz will be enabled. The Alaska
Emergency Channel will be found between the Memory
channels “P-1” and “01 (or 1-01).”
I
gency Channel, 5167.5 kHz.
Available Values: EnA(ENABLE)/diS(DISABLE)
Default Setting: diS(DISABLE)
When this Menu Item is set to “EnA(ENABLE),” the spot
frequency of 5167.5 kHz will be enabled. The Alaska
Emergency Channel will be found between the Memory
channels “P-1” and “01 (or 1-01).”
I
MPORTANT
:
The use of this frequency is restricted to stations operat-
ing in or near Alaska, and only for emergency purposes
(never for routine operations). See §97.401(c) of the
FCC’s regulations for details.
ing in or near Alaska, and only for emergency purposes
(never for routine operations). See §97.401(c) of the
FCC’s regulations for details.
TX AUDIO G
ROUP