DSC pc1616 ユーザーズマニュアル

Press the 

 (F),  

(A) or 

 (P) key for 2 seconds to generate a Fire, Auxiliary or

Panic alarm. The keypad sounder will beep indicating that the alarm input has been

accepted and transmission to the central station is underway.  Ask your alarm com-

pany if the emergency keys are available on your system

.

Press and Hold both keys simultaneously for 2 seconds to send the following mes-

sages:

Fire message

, 

Auxiliary message

, 

Panic Message

.

The system can generate 2 different alarm sounds:

•

Continuous Siren = Intrusion (Burglary Alarm)

•

Temporal / Pulsed Siren = Fire Alarm

If the fire alarm was accidental (i.e. burned toast, bathroom steam, etc.), enter your

Access Code to silence the alarm. Call your central station to avoid a dispatch. Ask

your alarm company if your system has been equipped with fire detection.

To reset the detectors, see the Sensor Reset section.

Keypads have 5 programmable one-touch function buttons located in a column down

the right-side of the keypad.  These buttons can also be activated by pressing and

holding number [1] through [5] respectively for 2 seconds.  The default for these

function buttons on the PK series keypads are as follows:

[1] Stay Arm

[2] Away Arm

[3] Chime Enable/Disable

[4] Fire/Reset - Command Output# 2

[5] Quick Exit

Any system keypad can be used to program or perform any keypad command.  LED

keypads use status and zone indicator lights to represent alarm functions and status.

The LCD keypad provides a written description as well as status indicator lights rep-

resent alarm functions and status. This section provides basic information regarding

keypad commands.  Refer to the PC1616/1832/1864 Reference Manual for detailed

description of all keypad commands.

The Ready light must be ON to arm the system.  If the Ready light is OFF, ensure all

protected doors and windows are secure or bypassed.  To arm the system in the Away

mode, either press and hold the Away function button for 2 seconds or enter a valid

user code and leave the premises through a door programmed as Delay.  Upon arm-

ing, the Armed light will turn ON.  If a user code was used to arm the system and

Stay/Away zones are programmed, the Bypass light will turn ON and will turn OFF

when a door programmed as Delay is violated.  If the Audible Exit Delay option is

enabled, the keypad will beep once every second during the exit delay (and three

times a second during the last 10 seconds) to alert the user to leave.  

The Ready light must be ON to arm the system.  If the Ready light is OFF ensure all

protected doors and windows are secure or bypassed.  To arm the system in the Stay

mode, either press and hold the Stay function button for 2 seconds or enter a valid

user code and stay within the premises (do NOT violate a door programmed as

Delay).  Upon arming, the Armed light and Bypass light will turn ON.  If the Stay

function button is used, the keypad will not beep during the exit delay to avoid

annoying the person staying in the premises.  If a user code was used, the keypad

will beep if the Audible Exit Delay option is enabled

.

The user must enter through a door programmed as Delay.  Upon entering, the key-

pad will emit a steady tone (and emit a pulsing tone during the last 10 seconds of

entry delay) to alert the user to disarm the system.  Enter a valid user code to disarm

the system.  If an alarm occurred while the panel was armed, the Memory light and

the zones that went into alarm will be flashing (LED keypad) or the keypad will dis-

play ‘Alarm in Memory’ (LCD keypad). Press the [#] key to return the keypad to the

Ready state.

4

[4][1] Bypass/Re-activate Stay/Away Zones

Press [4][1] to enter the bypass mode.  If the Code Required for Bypass option is

enabled, enter a valid user code.  The Bypass light will flash.  The keypad will turn

ON the corresponding zone light to indicate a zone is bypassed.  To bypass or unby-

pass a zone, enter the 2-digit zone number.  Once the correct zones are bypassed,

press [#] to exit.  The Bypass light will be ON if any zones are manually bypassed.
LCD Keypad:

Press [4][1] to enter the bypass mode.  If the Code Required for Bypass option is

enabled, enter a valid user code.  The keypad will display ‘Scroll to View Zones’.

The keypad will display the programmed zone labels for the zones and include the

letter ‘O’ in the bottom, right corner if the zone is violated or the letter ‘B’ if the

zone is bypassed.  Scroll to the appropriate zone and press the [4] key to change the

bypass status (or enter the 2-digit zone number).  Once the correct zones are

bypassed, press [#] to exit.
Additional Bypass Commands:

Press [99]. Recalls the last group of zones bypassed

Press [00]. Clears the bypass on all zones.

Press [95]. Saves zones that are manually bypassed.

Press [91]. Recalls the bypassed zones that were saved.

Reactivate Stay/Away Zones:
Press [4][1] when the system is armed in the Stay mode to change the armed status

to Away mode.  The system will add the Stay/Away zones back into the system after

the exit delay time expires.

[4][2] Trouble Display

•

Press [✱][2] to view a trouble condition. 

•

The trouble light will flash and the LCD will display the first trouble condition 

present.  

•

Use the arrow keys to scroll through all trouble conditions present.

 

•

Press [✱][2] to view a trouble condition.  

•

The trouble light will flash.  

•

Refer to the Trouble Summary below to determine the trouble condition(s) present

•

.

[4][3] Alarm Memory Display

The Memory light will be ON if an alarm occurred during the last armed period.

Press [4][3]. The Memory light will flash and the keypad will display the zones that

went into alarm

.

[4][4] – Door Chime Enable/Disable

Press [4][4]. The keypad will emit 3 rapid beeps if the door chime feature is now

enabled and a steady 2-second tone if it is now disabled.  The same function can be

performed by pressing and holding the Chime function button for 2 seconds.

[4][5] – Program User Codes

The following table identifies available user codes:

LED Keypad:
Press [4][5] followed by the Master Code. The Program light will flash. The keypad

will turn ON the corresponding zone light to indicate a user code is programmed.

Enter the 2-digit user to be programmed.  The zone light will flash. Enter a new 4 or

✱

✱

 [1]

✱

 Service Required -Press [1] for more information
[1] 

Low Battery

[2] Bell Circuit

[3] General System Trouble

[4] General system Tamper

[5] Module Supervision

[6] RF Jam Detected

[7] PC5204 Low Battery

[8] PC5204 AC Failure

 [2]

AC Trouble

 [3]

Telephone Line Trouble

 [4]

Failure to Communicate

 [5]

✱

Zone Fault -Press [5] for more information

 [6]

✱

Zone Tamper - Press [6] for more information

 [7]

✱

Wireless Device Low Battery - Press [7] for more information

 [8]

Loss of Time or Date

[01] – [32]

[33] – [34]

[40]

[41] – [42]

General User Codes

Duress Codes

Master Code

Supervisor Codes

arm, disarm

transmit duress reporting code

all functions

arm, disarm, program user codes