K-Mark Industrial Limited. UBC-CO1-ACC-R1 ユーザーズマニュアル

BarkWise™

Instruction Manual

4. Remote control

Press the button to activate

BarkWise™ (a blue LED light will

indicate the button is pressed).

This will activate the unit based

on your control panel settings.

Use the remote control up to

75 feet away.

Bark sensitivity slider

Allows you to adjust BarkWise™ sensitivity to barking.

This ranges from low to high.

REM (Remote Only or Mic)

Choose between having Barkwise™ activate when your

dog barks (UP) or only by pushing the button on the

included remote (DOWN).

AUD (Audible / Ultrasonic Mode)

Use either Ultrasonic mode (UP) or Audible mode (DOWN)

for training your dog. Audible mode is useful for hearing

the device activate to your dog’s bark, letting you know

that the bark sensitivity slider is set correctly.

VIB (Vibration / No Vibration)

Select BarkWise™ to vibrate (DOWN) or not vibrate (UP) in

response to barking.

6. Testing

Turn the sensitivity dial all the way up and power the unit ON.

Clap your hands to mimic the sound of barking. Depending

on what setting the unit is on, a flashing blue light will let you

know the unit is working.

7. Fit BarkWise™ on your dog

1. Make sure your dog is standing and is calm.

2. Place BarkWise™ underneath your dog’s neck

and ensure the vibration prongs are touching

his skin.

3. Adjust the collar so that it is snug but not

restricting. You should be able to place

1 finger comfortably between the nylon

strap and your dog’s neck.

4. Slip the loose end of the collar under the

attached loop.

4. After wearing the collar for a short

time period, recheck to see if it’s fitting

properly. Continue to do this periodically

as your dog becomes more comfortable

with BarkWise™.

6. If the collar length is too long, mark the trim length with a

pen, then remove the collar. Cut the excess and carefully

seal the frayed end with a flame. Fit the collar to your dog’s

neck and tuck in the strap using the provided loop.

5. Control panel

Note

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-

able protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in ac-

cordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

We’re Here to Help

Toll Free: 1-800-657-8214
Outside US: 1-541-245-4488

Caution

Changes or Modications not expressly approved by the party responsible could void the

user’s authority to operate this device.

Warning

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions. This product need power supply by adapter that can meet

LPS. The maximum operating temperature is 45°C.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

Website: www.ultimatebarkcontrol.com
Email: customerservice@goodlifellc.com

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en comprom-

ettre le fonctionnement.