Navico Inc. HS35 ユーザーズマニュアル
Section 4 - Radio setup menu (RADIO SETUP)
Hold down CALL/MENU key for about 1 second to access the following RADIO SETUP
options.
The following menu options are explained in this section.
options.
The following menu options are explained in this section.
RADIO SETUP
UIC *
Section 4-1
CH NAME
Section 4-2
RING VOLUME
Section 4-3
KEY BEEP
Section 4-4
UNITS
Section 4-5
INT SPEAKER
Section 4-6
WATCH MODE *
Section 4-7
WX ALERT *
TONE ALERT
Section 4-8-1
SAME ALERT
Section 4-8-2
SAME CODE
Section 4-8-5
COM PORT
Section 4-9
GPS SOURCE
Section 4-10
FAV CH SETUP *
Section 4-11
* Model dependant
See sections 1-3 and 1-4 if you want to know how to move around the menu and enter, save
and change data.
and change data.
4-1 Channel (UIC)
US and AUS models only.
Toggle between USA, International, or Canadian channel banks. The selected channel bank
is displayed on the LCD along with the last used channel. All the channel charts are shown in
Appendix C.
is displayed on the LCD along with the last used channel. All the channel charts are shown in
Appendix C.
RADIO SETUP
►UIC
CH NAME
RING VOLUME
KEY BEEP
▼
UIC
►USA
INT L
CANADA
1.
Select RADIO SETUP then UIC.
2.
Select the desired channel bank then press ENT.
4-2 Channel names (CH NAME)
The channel charts are listed in Appendix C with their default name tags. CH NAME gives you
the option to edit or delete the channel name tags displayed on the LCD.
the option to edit or delete the channel name tags displayed on the LCD.
In this example, the channel name tag PHONE-PORTOP associated with channel 87 is being
changed to CALL PORT OP.
changed to CALL PORT OP.
3-6-7 GPS alert (GPS ALERT)
If the GPS Alert is ON and the GPS navigation receiver is disconnected, the alarm sounds.
Note: The default setting is ON for the RS35 EU and OFF for the RS35 US.
MENU SELECT
LOCAL/DIST
▲
CONTRAST
►GPS/DATA
RADIO SETU
▼
GPS/DATA
MANUAL
►SETTING
SETTING
TIME DISPL
▲
LL DISPLY
COG/SOG
►GPS ALERT
GPS ALERT
►ON
OFF
1.
Select GPS/DATA then SETTING.
2.
Select GPS ALERT.
3.
Select ON (on) or OFF (off ) as desired.
3-7 GPS simulator (GPS SIM)
The GPS simulator is set to OFF whenever the radio is turned ON or whenever real GPS data
is available through the COM port. (The GPS simulator will not operate if a GPS signal is
received).
is available through the COM port. (The GPS simulator will not operate if a GPS signal is
received).
However, if you want to test it, turn it ON. Note that DSC transmissions will be blocked while
the GPS simulator is ON.
the GPS simulator is ON.
MENU SELECT
RADIO SETU
▲
DSC SETUP
AIS SETUP
►GPS SIM ▼
GPS SIM
ON
►OFF
1.
Select GPS SIM.
2.
Select ON (on) or OFF (off ) as desired.
3-8 Reset to factory defaults (RESET)
Use this to return every setting to the factory defaults except all MMSI settings and the
entries in your buddy list.
entries in your buddy list.
MENU SELECT
DSC SETUP
▲
AIS SETUP
GPS SIM
►RESET
RESET RADIO
ARE YOU SURE
YES
►NO
1.
Select RESET. The radio asks for confirmation.
2.
Select YES then press ENT to confirm and reset the radio. The menu is displayed again.
Simrad - RS35 Operation Instructions
Simrad - RS35 Operation Instructions
29
28