ELDAT GmbH RT24 ユーザーズマニュアル

RT24    

Hand Transmitter

 

 

 

 

 

 

LED

OPEN

STOP

Channel

selector

Mounting plate

CLOSE

 

 

LED

ON

Channel

selector

Mounting plate

OFF

 

 
 
 
 

 

 
 
 
 
 
 
 
 
 

 
 

Operating instructions 

 

 

Carefully read through these 
instructions before using the 
transmitter! 

Note also the operating instructions of the 
radio control(s)! 

The hand transmitter should only be oper-
ated within sight of the devices to be con-
trolled! Otherwise persons could be placed 
in danger! 

Have faulty hand transmitters checked by 
the manufacturer! 

Do not make any unauthorized alterations 
or modifications to the hand transmitter! 

 

RT24-3101M-01: 
1 radio channel for controlling one device, 
Functions: OPEN, STOP, CLOSE 

RT24-3101M-03: 
1 radio channel for controlling one device, 
Functions: ON and OFF 

RT24-3104M-01: 
4 radio channels for separate or contempo-
raneous controlling (group function) of four 
devices, 
Functions: OPEN, STOP, CLOSE 

RT24-3104M-03: 
4 radio channels for separate or contempo-
raneous controlling (group function) of four 
devices, 
Functions: ON and OFF 
 

- Hand transmitter incl. battery 

- Mounting plate 

- Programming connector 

- Screws and anchors 

- Adhesive pad 

- Operating instructions 
 

 

The hand transmitter comes with a battery 
already installed so, once unpacked, it is 
ready for immediate use. 
•  Mount the transmitter to the wall using 

the mounting plate. 

 

 

 

•  Transmit the channel(s) to the radio 

controls of the devices to be operated. 
For this read the operating instructions 
supplied with the radio controls. 

Note for 4-channel transmitters: channel 
selection is described in the chapter "Select-
ing channel". 

 

Only 4-channel transmitters:  

Using the channel selector button, select the 
channel of the device to be operated. 

 

2s

2s

2s

2s

2s

Channel 1

Channel 2

Channel 3

Channel 4

Channels 1-4
(Group function)

 

 

Each time you press the channel selector 
button, you switch to the next channel or to 
the group function (channel 1 > channel 2 > 
channel 3 > channel 4 > channels 1-4/ group 
function > channel 1 etc.). 
The selected channel is signalled via the 
LED’s as follows: 

 

Channel 1: 

LED 1 lights up for approx. 2 secs. 

Channel 2: 

LED 2 lights up for approx. 2 secs. 

Channel 3: 

LED 3 lights up for approx. 2 secs. 

Channel 4: 

LED 4 lights up for approx. 2 secs. 

Channels 
1-4: 

LED’s 1-4 light up for approx 2 secs. 
(group function) 

After the first pressing of the channel selector 
button, the channel used last is selected. 
 

•  Press one of the function buttons (OPEN, 

STOP, CLOSE or ON, OFF) in order to 
control the corresponding device. The 
LED of the corresponding channel briefly 
lights up. 

 

 

       

 

 
 

(Only 4-channel transmitters) If the group 
function is selected, all 4 devices are con-
trolled and all 4 LED’s briefly light up at the 
same time. 
 

•  If the LED(s) light up too faintly: 

change the battery. 

•  If the LED(s) don't light up at all: 

check that the battery is correctly poled. 

•  If the device still doesn't react: 

go closer to the radio control or re-
transmit the transmitter channels to the 
radio control.