Guangzhou Chiyuan Electronic Co. Ltd. N-4Q ユーザーズマニュアル
R/C
Introduction Manual
8
2.10.3 SYS (MIX)
2.10.4 SYS (HOLD)
SYSTEM
SYSTEM
MIX
ST: L 50 R 50
ST : L 50 R 50
EN: ON OFF
ST : L 50 R 50
EN: ON OFF
!
MIX allows three custom channels mixing. There are main channel and sub-channel
in the mix selection. The servo travel value of the sub channel is changed along with the
change of the main channel according to the setting rate.
change of the main channel according to the setting rate.
- In the power on interface, press “ENTER” to enter function interface, and select
“SYS” by “+” or “-”. Now press “ENTER” to enter “SYSTEM” menu and select “MIX”
by “+” or “-“. and then press “ENTER” and come to the mix setting interface.
by “+” or “-“. and then press “ENTER” and come to the mix setting interface.
- Firstly main channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L
and R separately correspond to the rate of Left and Right servos of the main channel mix
- Secondly sub channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L
and R separately correspond to the rate of Left and Right servos selected in the sub
channel.
channel.
- “EN” . is the start or close switch of this function. Select “ON” to start the function,
and “OFF” to close the function.
For example: current setting: ST: L 50% R 30%
TH: L 20% R 50%
EN: select “ON”
If throttle servo is 60% on the right and rudder servo is 50% on the right, and then
TH: L 20% R 50%
EN: select “ON”
If throttle servo is 60% on the right and rudder servo is 50% on the right, and then
after setting, throttle servo is: 50*30%+60%*50%=45%.
- Throttle servo will act along with the action of rudder servo.
Leave the setting by pressing “EXIT” when the setting is finished.
Leave the setting by pressing “EXIT” when the setting is finished.
SYSTEM
SYSTEM
MIX
TH: L 50 R 50
ST : L 50 R 50
EN: ON OFF
ST : L 50 R 50
EN: ON OFF
SYSTEM
SYSTEM
MIX
TH: L 50 R 50
ST : L 50 R 50
EN: ON OFF
ST : L 50 R 50
EN: ON OFF
SYSTEM
SYSTEM
VALUE : 0 %
HOLD
THRO.HOLD:
THRO.HOLD:
- Throttle hold can be performed by pressing the
switch to stop the engine. It can be performed for
accident braking. When pressing the switch, throttle
trigger doesn't work until the switch is pressed again.
accident braking. When pressing the switch, throttle
trigger doesn't work until the switch is pressed again.
- In the power on interface, press “ENTER” to
enter function interface, and select “SYS” by “+” or
“-”. Now press “ENTER” to enter “SYSTEM” menu
and select “HOLD” by “+” or “-“. and then press
“ENTER” and come to the throttle hold interface.
“-”. Now press “ENTER” to enter “SYSTEM” menu
and select “HOLD” by “+” or “-“. and then press
“ENTER” and come to the throttle hold interface.
- “VALUE” refers to servo value in throttle hold position. Value range:-120~ +120%
;Default value:0% .
R/C
Introduction Manual
3
2.2 Characteristics of system
2.1 MENU FUNCTION
FUNCTION
FUNCTION
Mod00
Mod00
10.2v
D/R:
100
HLD:
OFF
MOD:
HRF
ST.
ST.
TH.
TH.
V
LOGO
MODEL NAME
ST. Trim
TH. Trim
MODE(2.4G)
TH. HOLD
ST. D/R
EPA D/R
MDL ST.C
!
Respectively adjust EPA of three channels
!
Support D/R function of Steering channel
!
Neutral trims of Steering and throttle
!
Respectively set the reverse of the three channels
!
Choose EXP curve or LINE curve freely, and line curve can adjust the two ends.
!
Custom model name, 5 letters at most for each name, 16 memories model data. Each
data can be duplicated between them to avoid repeat establishment.
!
Battery change reminding function.
TRIM REV
SYSTEM
SYSTEM
MOD B-MIX
F/S RESET
MIX HOLD
TH.C SYS