Guangzhou Chiyuan Electronic Co. Ltd. N-4Q ユーザーズマニュアル
R/C
Introduction Manual
2.11 Trim ADJ.
10
!
Please start the motor or the engine while marking the adjustment of these settings.
1 .Connect the receiver, servos, and other components and then turn on the power
switches to transmitter and receiver.
2.Be sure the Steering trim and Throttle trim on the transmitter are at their neutral
position.
switches to transmitter and receiver.
2.Be sure the Steering trim and Throttle trim on the transmitter are at their neutral
position.
3.When turning on the transmitter, please make sure the transmitter antenna is
completely extended. Turn on the transmitter before turning on the receiver, while
turn off the receiver before turning off the transmitter.
completely extended. Turn on the transmitter before turning on the receiver, while
turn off the receiver before turning off the transmitter.
Steering Trim
Steering neutral adjustments can be made by moving the steering trim knob to the left or
the right.
!
the right.
!
Racers Tip
Always check and be sure the servo is at its neutral position before installing a servo.
Adjust the servo horn hole position and linkage so both are parallel. When a servo saver is
used place it as closer to center position as possible. Be sure the steering trim on the
transmitter at the neutral position.
used place it as closer to center position as possible. Be sure the steering trim on the
transmitter at the neutral position.
!
Trim Operation And Maximum Trav.
Changing the trim can effect the overall settings, when adjustments are made with the
trims, please recheck your installation for maximum servo travel.(Sreeting EPA right side
and left side ).
Changing the trim can effect the overall settings, when adjustments are made with the
trims, please recheck your installation for maximum servo travel.(Sreeting EPA right side
and left side ).
!
When Trim movement goes to extremes
That means if you make a lot of trim movement to get a servo to the neutral position,
please reposition the servo horn or servo saver on the servo and inspect your linkage
installation.
That means if you make a lot of trim movement to get a servo to the neutral position,
please reposition the servo horn or servo saver on the servo and inspect your linkage
installation.
Throttle Trim
Throttle neutral adjustments can be made by moving the throttle trim to the left or the
right.
right.
!
Racers Tip
When using a electronic speed control, please set the throttle trim to neutral and make
adjustments to the speed control. On a gas powered model, set the trim to neutral and
adjust the linkage to the point where carburetor is fully closed in accordance with the
engine instruction manual.
adjustments to the speed control. On a gas powered model, set the trim to neutral and
adjust the linkage to the point where carburetor is fully closed in accordance with the
engine instruction manual.
!
Trim Operation and Travel
Trim adjustments will effect the overall servo travel, so please check the (back-ward)
movement after the adjustment
movement after the adjustment
!
When trim movement is goes to extremes
That means if you make a lot of the trim movement to get the servo to the neutral
position, please recenter the servo horn closer to the neutral position and inspect your
throttle linkage.
position, please recenter the servo horn closer to the neutral position and inspect your
throttle linkage.
R/C
Introduction Manual
1
Caution
!
To work your R/C with your models correctly and safely, read this manual
carefully and keep it in a safe way as a reference introduction in the future.
carefully and keep it in a safe way as a reference introduction in the future.
!
Warning:
1. This product is only equipped for radio controlled models;
2. The usage of this product should be approved by local relevant law or
regulations;
3. We will be not responsible for the damages caused by unauthorized
modification, adjustment or replacement of parts of this product;
4. The manual may be altered without prior notice. Please contact us if you have
any corrections or clarifications that should be made in the manual.
1. This product is only equipped for radio controlled models;
2. The usage of this product should be approved by local relevant law or
regulations;
3. We will be not responsible for the damages caused by unauthorized
modification, adjustment or replacement of parts of this product;
4. The manual may be altered without prior notice. Please contact us if you have
any corrections or clarifications that should be made in the manual.
!
Please pay more attention on the parts in this manual, which marked with
“warning”.
“warning”.
!
Because of disturbance, do not work your radio control system simultaneously
with others at the same frequency.
with others at the same frequency.
!
Before starting the transmitter, make sure the transmitter batteries are well
loaded .The voltage of transmitter batteries never be lower than 8.6V. And
please check and confirm that the servos are all well and properly connected.
loaded .The voltage of transmitter batteries never be lower than 8.6V. And
please check and confirm that the servos are all well and properly connected.
!
Please take off batteries from transmitter after flying and during the
transportation.
transportation.
!
Please check and have a test on control surfaces to confirm the transmitter
handling of each part prior to each takeoff. The frequencies of the module and
the receiver should be the same.
handling of each part prior to each takeoff. The frequencies of the module and
the receiver should be the same.
!
Keep the radio system away from moist, high temperature and strong shake. Do
not clean the product with solvent.
not clean the product with solvent.
!
The antenna do not touch anything else when power switch is turned on. Do not
leave this product and its accessories within the reach of small children.
leave this product and its accessories within the reach of small children.
!
Please use this product according to your local relevant law or regulation, we
are not responsible for any incidents or damages.
are not responsible for any incidents or damages.