Cardo Systems ER02 ユーザーズマニュアル
6
Answering Calls (Including
Voice Recognition Feature)
Voice Recognition Feature)
The ring tone for incoming calls increases
gradually. When you hear the ring tone (on the
headset), there are two ways you can answer
the call:
gradually. When you hear the ring tone (on the
headset), there are two ways you can answer
the call:
• Tap the CTRL button on your headset
once (Figure 2Figure 2)
• Assuming the Voice Recognition feature
is active (See Section 7 below), answer the
call by pronouncing loudly any word of
your choice within 7 seconds. If you
remain silent for 7 seconds the call will be
automatically rejected and the ringing will
stop.
call by pronouncing loudly any word of
your choice within 7 seconds. If you
remain silent for 7 seconds the call will be
automatically rejected and the ringing will
stop.
Figure 2
Terminating Calls
To terminate a call, tap the Reject/Redial/End
button, followed by a tone confirming the
termination (Figure 3)
button, followed by a tone confirming the
termination (Figure 3)
If the other party terminates the call first, no
action is necessary.
action is necessary.
Wait at least three seconds before pressing the
CTRL button to start voice dialing.
CTRL button to start voice dialing.
Figure 3
NOTE: If your mobile phone does not support
the handsfree protocol you will not be able to
end calls by pressing the Reject/redial/End
Button. Instead, please tap the CTRL button to
terminate calls.
the handsfree protocol you will not be able to
end calls by pressing the Reject/redial/End
Button. Instead, please tap the CTRL button to
terminate calls.
Volume Control
The scala-rider Team Set headset comes
equipped with AGC technology to
automatically adjust itself to the optimal
speaker volume. Its embedded sensors
equipped with AGC technology to
automatically adjust itself to the optimal
speaker volume. Its embedded sensors
continuously measure the ambient noise and
driving speed to make manual adjustment of
the volume buttons virtually unnecessary.
driving speed to make manual adjustment of
the volume buttons virtually unnecessary.
You can also adjust the volume anytime by
pressing the volume buttons one step at a time
(Figure 4). For each step of adjustment, you
will hear a short beep.
pressing the volume buttons one step at a time
(Figure 4). For each step of adjustment, you
will hear a short beep.
Figure 4
Call Reject
While you hear the ring tone on the headset,
there are two ways you can reject the call:
there are two ways you can reject the call:
• Tap the Redial/Reject/End button on your
headset to reject the call (FIG. 9).
• Assuming the VR feature is enabled (see
section 7 below), remain silent for 7
seconds to reject the incoming call.
seconds to reject the incoming call.
Redial
While no call is in progress, tap the
Redial/Reject/End button on your headset to
redial to the last number (FIG. 9).
Redial/Reject/End button on your headset to
redial to the last number (FIG. 9).
Intercom Functions
• To enable and disable the intercom
functions long press the Intercom button. 1
tone indicates enabled, and 2 tones
indicates disabled.
tone indicates enabled, and 2 tones
indicates disabled.
• To initiate an intercom conversation,
simply start talking while in standby mode.
• To disconnect an intercom conversation,
remain silent for 15 seconds
7. Voice Recognition
(VR) feature
The VR feature allows you to answer or reject
incoming calls by voice control without having
to remove your hands from the handlebars.
incoming calls by voice control without having
to remove your hands from the handlebars.
The default mode of this feature is ON.
Tap here to
answer a call
answer a call
Tap here to terminate a call
Press here to
increase the
volume
increase the
volume
Press here to
decrease the
volume
decrease the
volume