Proxim Wireless Corporation XB92WFR ユーザーズマニュアル
Advanced Configuration
Tsunami
®
800 & 8000 Series - Software Management Guide
50
After configuring the required parameters, click OK, COMMIT and then REBOOT.
5.2 Network
The Network tab allows to view and configure the network specific information of the device.
To view the current operating network mode of the device, navigate to ADVANCED CONFIGURATION > Network. If the
network mode of the device is configured in Bridge mode, then following screen appears:
network mode of the device is configured in Bridge mode, then following screen appears:
# Assuming that MTU is configured as 1514
* Assuming that MTU is configured as 2048
* Assuming that MTU is configured as 2048
For optimal performance, MTU should be configured same on both the ends.
Controller Status
This feature helps the user to manage the device through ProximVision™ Advanced controller
which automatically updates the device with the latest firmware, if device is using old
firmware.
which automatically updates the device with the latest firmware, if device is using old
firmware.
By default, controller status is set to Standalone Mode. When set to Controller Mode, the
device automatically discovers the controller and establishes a secure communication through
two-way authentication.
device automatically discovers the controller and establishes a secure communication through
two-way authentication.
:
•
Not Applicable to MP-8200-BSU-G; MP-8250-BS9-G; MP-8250-BS1-G;
MP-8200-BSU; MP-8250-BS9; MP-8250-BS1; MP-8100-SUA; MP-8150-SUR;
MP-8150-SUR-100; MP-8200-SUA; MP-8250-SUR; QB-8200-EPA-G/LNK-G;
QB-8250-EPR-G/LNK-G; QB-8200-EPA/LNK and QB-8250-EPR/LNK devices.
MP-8200-BSU; MP-8250-BS9; MP-8250-BS1; MP-8100-SUA; MP-8150-SUR;
MP-8150-SUR-100; MP-8200-SUA; MP-8250-SUR; QB-8200-EPA-G/LNK-G;
QB-8250-EPR-G/LNK-G; QB-8200-EPA/LNK and QB-8250-EPR/LNK devices.
•
Controller feature should be enabled in ProximVision™ Advanced also.
•
Appicable only when the device is in Bridge Network Mode.
LED Status
The configurable options: Disable, RSSI, and Sync.
•
By default, it is set to RSSI. The Received Signal Strength Indicator (RSSI) LEDs indicates that
the unit is powered on, and LEDs will glow based on the RSSI value indicating link status. By
default, all 5 LEDs will blink at an interval of 1 sec.
the unit is powered on, and LEDs will glow based on the RSSI value indicating link status. By
default, all 5 LEDs will blink at an interval of 1 sec.
•
If the LED Status is disabled, all LEDs will be turned off.
•
If it is set to Sync, the third LED behavior of the scaling mask will indicate the Sync status.
: LED Status is applicable only to 82x MP and QB devices.
SU Wireless MAC
Address
Address
This field is applicable only for a BSU. In order to monitor the SU link statistics, the user
should first configure the wireless MAC address of the SU. If the configured SU is
registered with the BSU, then the LEDs will glow based on the RSSI value else all the 5 LEDs
will blink. To get the SU Wireless MAC Address, navigate to MONITOR > WORP
Statistics >Interface 1 > SU Link Statistics
should first configure the wireless MAC address of the SU. If the configured SU is
registered with the BSU, then the LEDs will glow based on the RSSI value else all the 5 LEDs
will blink. To get the SU Wireless MAC Address, navigate to MONITOR > WORP
Statistics >Interface 1 > SU Link Statistics
.
Parameter
Description