Fisher Price T4839-10 ユーザーズマニュアル
9
10
11
12
Test transmitter and receiver reception each time you change location of use.
• Place the transmitter in the room where you intend to use it.
• Set the transmitter channel switch to the same channel as the receiver.
• Press the transmitter power button to turn the power ON. The power L.E.D. lights.
• Turn on a radio.
• Set the transmitter channel switch to the same channel as the receiver.
• Press the transmitter power button to turn the power ON. The power L.E.D. lights.
• Turn on a radio.
Nightlight Button
Power Button
and L.E.D.
and L.E.D.
Channel Switch
Testing Sound Reception
Power Button
and L.E.D.
and L.E.D.
Power Button
and L.E.D.
and L.E.D.
Channel
Switch
Switch
Channel
Switch
Switch
Range
Indicator
Indicator
Sound Lights
Power/Volume Dial
Testing Sound Reception
• Place a receiver in the room where you intend to use it.
• Set the receiver channel switch to the same channel as the transmitter.
• Turn the power/volume dial to turn the power ON. Wait a few seconds to see if you have a good
• Set the receiver channel switch to the same channel as the transmitter.
• Turn the power/volume dial to turn the power ON. Wait a few seconds to see if you have a good
signal. If the range indicator light blinks along with beeping, you are out of range. Move the receiver
closer to the transmitter.
closer to the transmitter.
• When sound is picked up by the receiver, the sound lights turn on.
- One or two lights indicate quieter sounds.
- Three or more lights indicate louder sounds.
• If the range indicator begins fl ashing, you may be experiencing interference. Try selecting a different
- One or two lights indicate quieter sounds.
- Three or more lights indicate louder sounds.
• If the range indicator begins fl ashing, you may be experiencing interference. Try selecting a different
channel on both the receiver and transmitter. If the range indicator continues to fl ash, move the
receiver closer to the transmitter.
receiver closer to the transmitter.
• Place the transmitter in the same room with child. Point the microphone towards the crib or play area.
• Set the transmitter channel switch to the same channel as the receiver.
• Unwrap and fully extend the AC adaptor for best transmission. Insert the AC adaptor pin into the DC
• Set the transmitter channel switch to the same channel as the receiver.
• Unwrap and fully extend the AC adaptor for best transmission. Insert the AC adaptor pin into the DC
input jack on the transmitter and plug into a standard wall outlet. Use the AC adaptor only in a wall
outlet. Do not plug into a ceiling outlet.
outlet. Do not plug into a ceiling outlet.
Note: To use battery power, refer to the Battery Installation section.
• Press the transmitter power button to turn the power ON. The power L.E.D. will light.
• Press the nightlight button for a soft, glowing light. Press again to turn the nightlight off.
• Slide the nightlight timer switch to turn the timer
• Press the transmitter power button to turn the power ON. The power L.E.D. will light.
• Press the nightlight button for a soft, glowing light. Press again to turn the nightlight off.
• Slide the nightlight timer switch to turn the timer
on. When the timer is on the nightlight will
automatically shut off after 30 minutes. To turn the nightlight back on for another 30 minutes,
simply press the nightlight button again.
simply press the nightlight button again.
Nightlight Button
Power Button
and L.E.D.
and L.E.D.
Channel Switch
Setup and Use
Nightlight Timer Switch
Nightlight Timer Switch
Clock Set
• Turn receiver power ON.
• Press and hold the start/stop button to choose 12-hour or 24-hour clock format. Press the
• Turn receiver power ON.
• Press and hold the start/stop button to choose 12-hour or 24-hour clock format. Press the
reset button
to make a choice.
• Press the start/stop button . The hour number on the clock will fl ash. Press the reset button
to scroll through hour choices.
• Press the start/stop button . The minute numbers on the clock will fl ash. Press the reset
button
to scroll through minute choices.
• Press the start/stop button to confi rm your selections and complete the clock setup.
Receiver Battery Indicator
Transmitter Battery Indicator
Nightlight Indicator
Nap Timer
Nap Timer
Clock
Clock
Setup and Use
Nap Timer
Note: The nap timer will move to the top of the LCD screen when it is in use.
• Press the start/stop button to start the nap timer. Press again to stop the time.
• Press and hold the reset button to clear the timer.
Battery Indicator
• Displays the battery charge level of the receiver (1) and the transmitter (2). When battery power is
Note: The nap timer will move to the top of the LCD screen when it is in use.
• Press the start/stop button to start the nap timer. Press again to stop the time.
• Press and hold the reset button to clear the timer.
Battery Indicator
• Displays the battery charge level of the receiver (1) and the transmitter (2). When battery power is
low, the battery icon will appear partially fi lled.
Nightlight Indicator
• Indicates the transmitter nightlight is on.
• Indicates the transmitter nightlight is on.
SIDE VIEW
Channel
Switch
Switch