Fisher Price T4839-10 ユーザーズマニュアル
13
14
15
16
Range
Indicator
Indicator
Sound Lights
Setup and Use
• Place the receiver where you can see and hear it.
• To use AC power, unwrap and fully extend the AC adaptor cord for best reception. Insert the AC
• To use AC power, unwrap and fully extend the AC adaptor cord for best reception. Insert the AC
adaptor pin into the DC input jack on the receiver and plug into a standard wall outlet. Use the AC
adaptor only in a wall outlet. Do not plug into a ceiling outlet.
adaptor only in a wall outlet. Do not plug into a ceiling outlet.
Note: To use battery power, refer to the Battery Installation section.
• Turn the power/volume dial to turn the power ON. Turn the dial to adjust the volume to a comfortable
• Turn the power/volume dial to turn the power ON. Turn the dial to adjust the volume to a comfortable
listening level.
• Clip the receiver onto your clothes to stay in touch with baby around your house or yard.
Hint: The receiver’s range is up to 900 feet (274 m) away from the transmitter. The range indicator
will fl ash and you will hear beeping when the receiver is out of range.
will fl ash and you will hear beeping when the receiver is out of range.
Problem
Solution
Receiver range indicator light flashes
and you hear beeping
and you hear beeping
Receiver is out of range of transmitter. Move receiver closer to transmitter.
Note: Range varies depending on surrounding conditions such as noise
levels, physical obstructions and signal interference.
Note: Range varies depending on surrounding conditions such as noise
levels, physical obstructions and signal interference.
Channel switch on transmitter and receiver are not the same. Switch
transmitter and receiver to the same channel.
transmitter and receiver to the same channel.
Transmitter power is off. Turn transmitter power on.
Batteries in receiver are weak or dead. Replace all batteries with three
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
No power to wall outlet and transmitter power is off. Make sure light
switch that controls power flow to wall outlet is on.
switch that controls power flow to wall outlet is on.
Power is off because circuit breaker for room is off. Make sure house fuses
and circuit breakers are on.
and circuit breakers are on.
Receiver power L.E.D. does not light
at all
at all
Receiver power is off. Turn receiver power on.
Batteries in receiver are weak or dead. Replace all batteries with three
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
Power is off because circuit breaker for room is off. Make sure house fuses
and circuit breakers are on.
and circuit breakers are on.
No power to wall outlet and power is off. Make sure light switch that
controls power flow to wall outlet is on.
controls power flow to wall outlet is on.
Receiver (1)/transmitter (2) battery
indicator is only partially filled
indicator is only partially filled
Batteries are weak or dead. Replace all batteries with new “AAA” (LR03)
alkaline batteries or use the AC adaptor as a power source.
alkaline batteries or use the AC adaptor as a power source.
Receiver screen is fading
Batteries are weak or dead. Replace all batteries with new
“AAA” (LR03) alkaline batteries or use the AC adaptor as
a power source.
“AAA” (LR03) alkaline batteries or use the AC adaptor as
a power source.
Transmitter power L.E.D. does not
light at all
light at all
Transmitter power is off. Turn transmitter power on.
Batteries in transmitter are weak or dead. Replace all batteries with four
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
“AAA” (LR03) alkaline batteries or use the AC adaptor as a power source.
Check transmitter power cord plug-to-outlet connection.
No power to wall outlet and transmitter power is off. Make sure light
switch that controls power flow to wall outlet is on.
switch that controls power flow to wall outlet is on.
Power is off because circuit breaker for baby’s room is off. Make sure
house fuses and circuit breakers are on.
house fuses and circuit breakers are on.
You can hear conversations or
sounds from other homes
sounds from other homes
There is signal interference due to other nursery monitors on same channel
or cordless telephone use. Change channel switches on both transmitter
and receiver to eliminate source of interference.
or cordless telephone use. Change channel switches on both transmitter
and receiver to eliminate source of interference.
Clock/nap timer is not working or is
functioning erratically
functioning erratically
Reset the receiver by removing the batteries and replacing them in
the receiver.
the receiver.
Problems & Solutions
Hint: If, after checking all of these solutions, you believe that your transmitter power cord or AC adaptor are
damaged, please contact Fisher-Price
damaged, please contact Fisher-Price
®
.
ICES-003 NMB-003
ICES-003
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. L’utilisation de ce
dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fonctionnement du dispositif.
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. L’utilisation de ce
dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fonctionnement du dispositif.
Care
• Excess dirt in the transmitter microphone will hamper transmission of sound. Clean the outer surface
of the transmitter and the receiver with a cloth lightly dampened with a mild cleaning solution.
• Never immerse the transmitter, receiver or AC adaptors.
• Protect the environment by not disposing of this product with household waste (2002/96/EC).
Check your local authority for recycling advice and facilities (Europe only).
Power/Volume Dial
FCC Statement
(United States Only)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifi cations not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
Monitor
Model Number: T4839
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Monitor
Consumer Relations Department
636 Girard Avenue
East Aurora, New York 14052, U.S.A.
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifi cations not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
Monitor
Model Number: T4839
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Monitor
Consumer Relations Department
636 Girard Avenue
East Aurora, New York 14052, U.S.A.