Honeywell International Inc. 8DL6160VPADT ユーザーズマニュアル
- 2 -
4. Wire directly from the Touchpad’s terminal block to the
terminal block on the control panel. (Refer to Wiring
Table). Connect only the red and black Aux. Power
connections at the control panel.
Table). Connect only the red and black Aux. Power
connections at the control panel.
Wiring Table
Touchpad
Control Panel
Wire Color
G Data
In
Green
–
– Aux Pwr (GND)
Black
+
+ Aux. Pwr (POS)
Red
Y Data
Out
Yellow
5. Re-attach the Touchpad to the case back.
6. Remove clear protective film from LCD display.
SETTING THE TOUCHPAD OPTIONS
The procedures that follow are used to set the Touchpad
address, voice chime mode, and additional voice Touchpad
mode.
Setting the Touchpad Address
The procedures that follow are used to set the Touchpad
address, voice chime mode, and additional voice Touchpad
mode.
Setting the Touchpad Address
When used with the Safewatch Pro/Security Manager
3000 control panels, address 16 must be assigned to
the first Touchpad. Additional Touchpads must be
set at 17 - 23 and must be enabled additionally in
control programming (fields *190 - *196).
The Touchpad may be set for address 00-30 or for non-
addressable mode (31). The default Touchpad address is 31.
For valid address settings for your Touchpad, refer to the
control panel's Installation & Setup Guide.
Notes:
• If unable to enter the address mode, power down, power
addressable mode (31). The default Touchpad address is 31.
For valid address settings for your Touchpad, refer to the
control panel's Installation & Setup Guide.
Notes:
• If unable to enter the address mode, power down, power
up, and try again.
• If 10 seconds pass with no key entry, the Touchpad
automatically exits the address mode. You must power
down, power up, and start the address mode again.
down, power up, and start the address mode again.
• The Touchpad will not enter the address mode if the
control panel is in programming mode.
1. Apply power to the Touchpad.
2. Within 60 seconds of applying power to the Touchpad,
press and hold down the [1] and [3] keys at the same time
for 3 seconds. The current Touchpad address will be
displayed.
for 3 seconds. The current Touchpad address will be
displayed.
3. Press "00". The current address is cleared.
4. Enter desired two-digit Touchpad address.
5. Press [
✱] to accept the displayed address and enter the
Voice Chime Mode. "VOICE CHIME" is displayed along
with the selected mode "1" or "0".
with the selected mode "1" or "0".
Setting The Voice Chime Mode
Setting Voice Chime mode off does not effect the
voice status or alarm annunciation.
1. Press [1] to set the Voice Chime mode on or press [0] to
set the Voice Chime mode off.
2. Press [
✱] to save the displayed Voice Chime mode and
enter the Additional Console Voice Touchpad mode.
"ADDITIONAL CON" is displayed along with the
selected mode "1" or "0".
selected mode "1" or "0".
Setting the Additional Console Mode
The Additional Console mode must be set for all voice
Touchpads being used.
1. Set the voice Touchpad Additional Console mode as
The Additional Console mode must be set for all voice
Touchpads being used.
1. Set the voice Touchpad Additional Console mode as
follows:
a. On the Primary voice Touchpad, press [0] to set the
Additional Console mode to NO.
b. On any secondary voice Touchpads, press [1] to set
Additional Console mode to YES.
2. Press [
✱] to save the mode and enter Prox Address Mode.
Setting the Prox Reader Address
1. After exiting “touchpad address” mode, the prox reader
1. After exiting “touchpad address” mode, the prox reader
will begin communicating with the touchpad, and the
touchpad will display “Prox Addr? XX” on the first line.
touchpad will display “Prox Addr? XX” on the first line.
XX = the current ECP Address.
2. Enter an appropriate ECP address. Set the current
address to "00": Press [0] to clear the current "tens"
digit. The cursor moves to the "ones" digit position.
Press [0] to clear the current "ones" digit. The cursor
moves back to the "tens" digit position.
digit. The cursor moves to the "ones" digit position.
Press [0] to clear the current "ones" digit. The cursor
moves back to the "tens" digit position.
3. Enter the appropriate address: Enter the proper "tens"
digit of the address. The cursor moves to the "ones" digit
position. Enter the proper "ones" digit of the address.
position. Enter the proper "ones" digit of the address.
4. Press the * key to save the entry. The keypad will beep
three times confirming the address is accepted, and the
first digit of the address will flash. You can re-enter the
address if desired.
first digit of the address will flash. You can re-enter the
address if desired.
5. Power down the Touchpad.
6. Connect the green and yellow data in and data out wires
at the control panel. Once connected, any touchpad not
enabled in the control at that point will be blank.
enabled in the control at that point will be blank.
ENROLLING PROX TAGS
Each prox tag is enrolled as a “User” in the alarm system.
When enrolling the tags, the last four digits of the tag’s
serial number should be used as the User Code. Refer to the
control’s User Guide for instructions on programming user
codes. When programming is complete, test the system to
ensure that each prox tag arms and disarms the system as
specified.
VIEWING THE TOUCHPAD ADDRESS
During normal operation, press and hold down the [1] key
and [3] key at the same time for about 3 seconds. The
current address is displayed. No key entry is allowed. Press
any key to exit or wait 10 seconds to exit the viewing mode.
During normal operation, press and hold down the [1] key
and [3] key at the same time for about 3 seconds. The
current address is displayed. No key entry is allowed. Press
any key to exit or wait 10 seconds to exit the viewing mode.
SPECIFICATIONS
Physical:
Physical:
5-5/16"H x 7-3/8"W x 1-3/16"D
Display:
2 x 16 Alpha-Numeric
Supertwist LCD (backlit)
Sounder:
Speaker
Electrical:
Voltage:
+12VDC
Current:
190mA (ARMED LED lit, LCD backlight
and sounder on) reduces to 60mA when
panel is operating in standby mode
(backlight off).
panel is operating in standby mode
(backlight off).