Computime Limited TLT-TX ユーザーズマニュアル

This wireless thermostatic on/off/ remote control – system pro-
vides a safe, reliable, and user-friendly remote control for millivolt
valve gas appliances.  The system can be thermostatically or man-
ually turned on and off with the transmitter.  Always check the
appliance home owner’s manual for additional information, or
warnings regarding accessory installation before connecting this
remote control system.

Carefully inspect the contents for shipping damage. If any parts
are missing or damaged, immediately contact the dealer from
whom you purchased the kit.  Do not attempt to install any part of
the kit unless all parts are in good condition.  Please keep this
booklet for future reference.

Description

Qty

Touch Light Transmitter

1

Battery Alkaline AA (for Transmitter and receiver)

6

Receiver (Assembly)  consists of :

1

Receiver Box
Slide Button-Black (On/RS/Off)
L-Bracket (Floor Mount)

Wall Cover Plate-Black

1

Wall Cover Plate-White

1

Slide Button-White (On/RS/Off)

1

Screws (for Wall Cover Plate)

2

Plug-In Wiring Assembly – 18" Inches

1

Velcro (Loop and Hook)

1

Wall Anchor Screws

2

Wall Anchor

2

Installation Instructions

1

Screws (for fireplace system control covers)

2 

Wall Bracket

1

• 

Contemporary Ergonomic Table Top or Wall Mount 
Transmitter with Large LCD Display

• Easy 

Access 

Thermostatic 

Control

• 

Battery Powered Transmitter and Receiver

• 

Easy Access Battery Door

• 

Pre-Programmed for Quick Installation

• 

Low battery Indication

• 

Child Proof Lock-out

• 

16 Security Codes

• 

2 hour Shut Down (Optional)

• 

Thermal Safety Shutdown (Transmitter Only)

• Quick 

Disconnect 

Wiring 

Assembly

• Reset 

Button

• 

Read this manual thoroughly prior to installing, programming 
or operating any remote control.

• 

This remote control system is designed for use with a milli
volt gas valve system.  Do not use this remote control system 
on applications with voltages above 24 Volts DC and 1 amp 
current.

• 

This remote control system requires two (2) "AA" alkaline 
batteries for the transmitter and four (4) "AA" alkaline 
batteries for the receiver.

• 

Wiring must conform to appliance requirement and building 
codes/ordinances as required by local and national code 
authorities having jurisdiction.

• 

Do not short (or jumper) across the gas valve terminals to test
the remote control installation. This could damage the unit 
and void the warranty.

• 

This remote control system should only be used as described 
in this manual.  Any other use is not recommended and will 
void the warranty.

The remote receiver may be wall mounted or installed in the appli-
ance per the appliance homeowner’s manual. Refer to the
Homeowner’s Manual for special installation instructions. If
wall mounted, the remote receiver must be installed in a junction
box with cover plate provided.  Failure to follow the installation
instructions found in the appropriate Homeowner’s Manual will
void the warranty and may cause a fire hazard.

Installing Batteries:

The remote receiver uses four (4) "AA"- size batteries.  To install
batteries,

1. Remove the slide switch by 

gently pulling straight out.

2. Use your thumb and index 

finger to gently pull down the 
L-bracket.

3. Open the battery door by 

pressing the two tabs located on
the door.

4. Install the batteries as indicated 

in the receiver cover.

5. Close the battery door until the 

door tab snaps in place. 

6. To install the receiver into a 

wall junction box, install the 
receiver with the screws 
provided .

7. If you decided to install the 

receiver into the appliance, rein
stall the L-bracket.

8. Gently, install the slide switch 

back to the receiver stem.

9. The batteries should be replaced

at least once every 6 months or 
when the battery indicator 
flashes.

Connecting the Receiver to your appliance:

This system comes with an 18 inch wire assembly.  Insert the
white terminal to the back of the receiver.  The terminal wire
block can only be installed one way.  Do not force the terminal
plug onto the receiver.   

Connect the wiring terminal two (2) 1/4" female spade terminals
to the appliance.  Refer to the appropriate Homeowner’s Manual
for proper wiring connections to the appliance.  Your appliance
may have other options to connect wiring from receiver.   For
applications longer than 18 inches, use 18 gauge wire, 105ºC
rated, with no splices.  Connect to the two (2) 1/4" female spade
wiring terminals.  Wire can be no longer than 20 feet.   

Installing Batteries:

The Touch Light transmitter uses two (2) "AA"- size batteries.  To
install batteries,

1. Press down the battery door tab and lift up and remove the 

battery door.

2. Install the battery.
3. Close the battery door by snapping in place
4. Repeat the above step for the other battery.
5. When both batteries are installed, the transmitter will initialize 

for 10 seconds and then is ready for use.

6. The batteries should be replaced at least once every 6 months or

when the battery  icon indicator flashes.

Setting Privacy (DIP) Switch on Receiver and Transmitter:

The remote receiver and transmitter privacy (DIP) switches are
preset at the factory.  In the event of activation or interference
from other nearby transmissions, reset the code using the follow-
ing procedure:

1. Slide the code switches on the transmitter or receiver to your 

choice of ON or OFF position.  Switches  #1 to #4 are preset to 
"ON" for both the transmitter and receiver.

2. The switches on the transmitter and receiver must match in 

order for the system to work. 

3. To check, touch the transmitter groove surfaces for at least 1 

second and, the transmitter will emit a beep, and the receiver 
indicator light will blink.  If not repeat step 2.

4. The system is now ready to operate.

Optional Auto Shutdown:

1. The Touch Light transmitter comes preset from the factory with 

a 2 hour shutdown from its last ON operation.  This is done to 
prevent the appliance from continuing to run if  unattended.

2. You may disable this feature if you wish.  To disable, change the

Touch Light transmitter privacy (DIP) switc #1 ONLY to the 
OFF position (by sliding the switch towards the battery door.)  
Make sure the receiver privacy (DIP) switches are set the same.
Follow the instructions on how to set the privacy (DIP) switch 
setting.

3. By disabling this feature, your appliance may continue to 

Reset Button:

1. The reset button can be used  to reset the transmitter if  

transmitter is not working properly.  The reset button is located 
behind the battery door cover. Using a paper clip, press the reset
button and the transmitter will reset and initialize for 10 seconds
before it can be used.

Where to place Touch Light Transmitter?

1. The Touch Light transmitter is recommended to be placed on a 

non metal table top or wall mount.  Make sure there is no direct
contact of metal parts to the body of the transmitter. 

2. If wall mount, choose a mouting location about 5 feet above the

floor in an area with good air circulation and away from the fol
lowing:

a. Air ducts
b. Radiant heat from the sun and appliances
c. Concealed pipes and chimneys

3. Align the wall bracket to the
desired location.  Mark two (2) 

holes using the wall bracket 
as template.

4. Drill two (2) holes and insert 

the plastic anchors until they 
are flush with the wall.

5. Fasten securely the wall 

bracket to the wall with the 
two (2) screws.

6. Refer to the figure on how to 

install the transmitter to the 
wall bracket.

Transmitter:
General:

The TLT has two operating modes.  It can used as manual or ther-
mostatic On/Off remote control system. 

The transmitter will operate the remote receiver from 1foot to a
maximum of 20 feet.  The operational range is reduced when bat-
teries are low or when the receiver is inside a metal enclosure.

Initial start up:

1. After initial power up or reset button is pressed, the transmitter 

is reset.  

2. During transmitter reset, all segments of the LCD will be turned 

on. After ten (10) seconds, the LCD will be initialized and 
operational.  You will hear a beep during this time.

3. After reset, only the room temperature will be displayed on the 

LCD display.

ALIGN THE TRANSMITTER MOUNTING
KEYHOLES TO THE PIN.  PUSH IN AND
SLIDE DOWN UNTIL SNAP.

MOUNTING TRANSMITTER
PIN

MOUNTING
HOLES

WALL BRACKET

WALL

MILLIVOLT VALVE

GENERIC WIRING DIAGRAM FOR RECEIVER. THE RECEIVER WIRE
NEED TO CONNECT TO THE VALVE AT THE "TH" AND "TH/TP"
JUNCTION

REMOTE CONTROL

RECEIVER

BATTERY
DOOR TAB

RESET BUTTON

TRANSMITTER

FACTORY PRESET DIP SWITCH SETTING

RECEIVER