Computime Limited TLT-TX ユーザーズマニュアル
Manual Mode- On or Off Operation:
1. Since Touch Light transmitter is touch sensitive equipment, we
recommend to use only your index finger to touch. Do not use
any metal object to contact or touch the surface. The transmitter
will recognize a valid touch if either side of the surface area are
covered more than 10% for a period of at least 2 second.
any metal object to contact or touch the surface. The transmitter
will recognize a valid touch if either side of the surface area are
covered more than 10% for a period of at least 2 second.
2. To activate a signal, you need to touch either side of the groove
surfaces for at least 2 second and then release your finger. If
the touch is valid, it will beep once and a signal will be sent to
the receiver. During this time you will see the transmission icon
on the LCD display for a brief time. No other command can
be given until the transmission is completed.
the touch is valid, it will beep once and a signal will be sent to
the receiver. During this time you will see the transmission icon
on the LCD display for a brief time. No other command can
be given until the transmission is completed.
Thermostatic Mode Operation:
1. Push down on the flip door button to access the thermostatic
control.
2. Press the AUTO button to enter the thermostatic mode.
"TSTAT" and SET temp icon will appear on the lower LCD
screen.
screen.
3. In thermostatic mode, press the ▲ button or ▼ DN button to set
the desired set temperature.
4. Once the setting is completed, the transmitter will automatically
turn on (beep once) the fireplace when the room temperature is
below the set temperature and turn off (beep once) the appliance
when the room temperature is above the set temperature within
1 degree.
below the set temperature and turn off (beep once) the appliance
when the room temperature is above the set temperature within
1 degree.
5. There will be a slight delay in the response of the unit (on/off)
to a temperature. Room temperature is monitored every 3
minutes.
minutes.
6. All the manual on/off touch will be diabled the the
transmitter is in thermostatic mode.
7. Press the Auto button to exit the thermostatic mode. The
"TSTAT" and SET temp icon will disappear on the lower LCD
display. The transmitter will be in the manual on/off mode
display. The transmitter will be in the manual on/off mode
Child-proof protection:
1. Touch both sides of the groove surface with your two index
fingers simultaneously for at least 3 seconds to enter child-proof
mode. Once you hear two (2) beeps and the child proof icon
appears on the LCD display, the child proof mode is activated.
You will not able to turn the appliance on or off in this mode.
mode. Once you hear two (2) beeps and the child proof icon
appears on the LCD display, the child proof mode is activated.
You will not able to turn the appliance on or off in this mode.
2. Always place both fingers on the middle of the groove surfaces
to ensure a proper touch.
3. Child-proof protection is not available in Thermostatic mode.
4. To deactivate child proof, repeat step 1. You will hear two (2)
4. To deactivate child proof, repeat step 1. You will hear two (2)
beeps and the child proof icon will disappear.
Safety Touch Auto Shut Off:
1. If a metal object, (i.e. car key) or your hand is resting
continuously for more than ten (10) seconds on either side of the
groove surfaces (NOT BOTH SURFACES), the transmitter
will emit three (3) beeps and send an off signal to turn off the
appliance. Once the object is removed from the groove
surfaces, the transmitter will remain in the off state until your
next valid touch. Never leave anything on top of the surface
of the touch light transmitter to prevent undesirable
operation.
groove surfaces (NOT BOTH SURFACES), the transmitter
will emit three (3) beeps and send an off signal to turn off the
appliance. Once the object is removed from the groove
surfaces, the transmitter will remain in the off state until your
next valid touch. Never leave anything on top of the surface
of the touch light transmitter to prevent undesirable
operation.
2. This feature will be disable in Thermostatic mode.
Low-battery detection:
1. Battery voltage is checked once a minute. When the battery
voltage drops to a certain level, the low-battery warning will
come on, and the transmitter will emit three (3) beeps and send
signals to turn off the appliance. The transmitter will not
function anymore until new batteries are installed.
come on, and the transmitter will emit three (3) beeps and send
signals to turn off the appliance. The transmitter will not
function anymore until new batteries are installed.
2. When the batteries are low, the LCD shows a blinking low
battery indicator.
3. Change the battery every six months before the battery is too
weak for normal operation. TURN THE UNIT OFF BEFORE
REPLACING BATTERIES.
REPLACING BATTERIES.
Touch Light Transmitter Thermal Shutdown:
1. If transmitter measures a room temperature exceeding 99
degrees Fahrenheit, the LCD will display "HI", emit three (3)
beeps and send an off signal to turn off the appliance.
beeps and send an off signal to turn off the appliance.
2. Transmitter will not function until the room temperature has
dropped below 99 degree Fahrenheit.
3. If transmitter measures a room temperature less than 40 degrees
Fahrenheit, the LCD will display "LO", and no signals will be
sent to turn on the appliance.
sent to turn on the appliance.
Receiver:
Slide Switch:
1. ON position: the system will remain on until the slide switch is
placed in the OFF or RS position.
2. RS position: the system will only operate if the remote receiver
receives a signal from the transmitter.
3. OFF position, the system is off. The slide switch should be
placed in the OFF position if you will be away for an
extended period of time. If the remote receiver is mounted
out of children’s reach, the OFF position also functions as a
safety device by both turning the system off and rendering the
receiver inoperable.
extended period of time. If the remote receiver is mounted
out of children’s reach, the OFF position also functions as a
safety device by both turning the system off and rendering the
receiver inoperable.
TESTING YOUR NEW REMOTE CONTROL
SYSTEM
1. Light your gas appliance following the appliance lighting
instructions that came with the appliance. Confirm that the pilot
light is on; it must be in operation for the remote control to
operate the main gas valve. Appliance control knob must be in
the ON position. Appliance ON/OFF switch must be in OFF
position.
light is on; it must be in operation for the remote control to
operate the main gas valve. Appliance control knob must be in
the ON position. Appliance ON/OFF switch must be in OFF
position.
2. Slide the 3 position button on the remote receiver to the ON
position. The main gas flame should ignite.
3. Slide the button to OFF. The flame should extinguish (the pilot
light will remain on).
4. Slide the button to RS (the center position), then touch the
transmitter to turn the system to ON. The main gas flame
should ignite.
should ignite.
5. Touch the transmitter to turn the system to OFF. The flame
should extinguish (the pilot light will remain on).
TROUBLESHOOTING
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
WARRANTY
This warranty gives you specific legal rights and you may also
have other rights that vary from
state to state or province to province. Answers to any questions
regarding our limited warranty may be obtained by writing our
corporate offices.
Ambient Technologies warrants each new Ambient Technologies
remote control against any defects that are due to faulty material
or workmanship to the original owner, for a period of five years
after the original date of purchase. This warranty and our liability
does not apply to batteries, nor does it include damage to mer-
chandise or the remote control resulting from accident, alteration,
neglect, misuse, improper installation or any other failure to fol-
low Ambient Technologies installation and operating instructions.
Ambient Technologies agrees to repair or replace at its option any
Ambient Technologies remote control under warranty provided it
is returned postage prepaid to our warranty facility in a padded
carton within the warranty period, with proof of the original date
of purchase and a brief description of the malfunction. This limit-
ed warranty does not include the cost of removal or re-installation.
have other rights that vary from
state to state or province to province. Answers to any questions
regarding our limited warranty may be obtained by writing our
corporate offices.
Ambient Technologies warrants each new Ambient Technologies
remote control against any defects that are due to faulty material
or workmanship to the original owner, for a period of five years
after the original date of purchase. This warranty and our liability
does not apply to batteries, nor does it include damage to mer-
chandise or the remote control resulting from accident, alteration,
neglect, misuse, improper installation or any other failure to fol-
low Ambient Technologies installation and operating instructions.
Ambient Technologies agrees to repair or replace at its option any
Ambient Technologies remote control under warranty provided it
is returned postage prepaid to our warranty facility in a padded
carton within the warranty period, with proof of the original date
of purchase and a brief description of the malfunction. This limit-
ed warranty does not include the cost of removal or re-installation.
Ambient Technologies
149 Cleveland Drive
Paris KY 40361
FOR TECHNICAL SUPPORT
CALL 800-398-6195
50D0093 Rev 2 Apr 2005
Symptom
1. LED light on receiver
blinking or battery icon
on LCD on transmitter.
on LCD on transmitter.
2. LCD display is blank
3. LCD display shows
3. LCD display shows
"funny" display
4. Appliance does not come
on after a valid touch
(beep)
(beep)
4. Receiver cannot receive
signal.
Causes
1. Low Battery
1. Wiring / Electrical
Connections
2. Privacy (DIP)
switch setting on
transmitter does not
match receiver
transmitter does not
match receiver
3. Transmitter measures
temperature
exceeding 99 degrees
Fahrenheit and
shows "HI" on LCD
exceeding 99 degrees
Fahrenheit and
shows "HI" on LCD
4. Distance between the
transmitter and
receiver is more than
30 feet
receiver is more than
30 feet
1. Receiver is installed
in an enclosure
Action
1. Replace batteries.
Change batteries every 6
months.
months.
2. Check battery installation
and replace batteries.
3. Press Reset button at the
back of the transmitter.
1. Slide the switch to ON, if
appliance comes ON,
wiring is not the cause.
wiring is not the cause.
2. If appliance does not
come on, check wiring
connections.
connections.
1. Make sure the transmitter
and receiver have the
same DIP switch settings.
same DIP switch settings.
1. Move transmitter to a
cooler place and wait
until temperature drops
below 99 degree.
until temperature drops
below 99 degree.
1. Make sure the operating
distance is less than 200
feet
feet
1. Make sure the receiver is
not located inside an
enclosure.
enclosure.
LCD Display During Initialization
LCD Display After Initialization
SET
TSTAT
TRANSMISSION
ICON INDICATES
A SIGNAL BEING
SEND TO THE
RECEIVER
ICON INDICATES
A SIGNAL BEING
SEND TO THE
RECEIVER
FLAME ICON
INDICATES
APPLIANCE IS ON
INDICATES
APPLIANCE IS ON
GROOVE
SURFACE
SURFACE
SET
TSTAT
AUTO
PUSH DOWN TO
OPEN FLIP DOOR
OPEN FLIP DOOR
FILP DOOR IN
OPEN POSITION
OPEN POSITION
LOW BATTERY
ICON
ICON