Futaba Corporation CGY760R-24G ユーザーズマニュアル
41
40
S
BUS
B
ASIC
M
ENU (S.BUS BASIC SETTING)
The SBUS basic screen is displayed from the basic menu screen (see page 39). Set
the CH for each function according to the transmitter to be used. Set unused functions
to INH. If a function is not going to be used, then it must be set to [INH]. If a func-
tion is not going to be used, then it must be set to [INH]. For example, if the Gain A/
E and Gain RUD remote gain functions are not going to be used, then set them to [INH]
and the CGY760R will then allow you to make gain adjustments within the respec-
tive menu.
the CH for each function according to the transmitter to be used. Set unused functions
to INH. If a function is not going to be used, then it must be set to [INH]. If a func-
tion is not going to be used, then it must be set to [INH]. For example, if the Gain A/
E and Gain RUD remote gain functions are not going to be used, then set them to [INH]
and the CGY760R will then allow you to make gain adjustments within the respec-
tive menu.
WARNING
Always verify that the S.BUS function
assignments match your transmitter’s
function (in the FUNCTION menu) assign-
ments. If any changes are made within the
transmitter function assignments, then it
will also be necessary to make the changes
within the S.BUS function assignments.
function (in the FUNCTION menu) assign-
ments. If any changes are made within the
transmitter function assignments, then it
will also be necessary to make the changes
within the S.BUS function assignments.
Settings (all in common):
1 to 16ch, DG1, DG2, INH
From 3/3
From 1/3
Go to 2/3 from any
cursor position
cursor position
From the "RESET" of
SBUS BASIC screen 3/3
SBUS BASIC screen 3/3
(1) S. BUS connection: AIL (Aileron) channel
Move the cursor to "AIL CH #" by pressing the [
/
+] or [
/
-] key and press
the [Enter] key to enter the setting mode. Use the [
/
+] or [
/
-] key to set
the aileron channel of the transmitter. When you are done, press [Enter]
key to inish.
key to inish.
(6) S. BUS connection: Gain A/E channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(7) S. BUS connection: Gain RUD channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(8) S. BUS connection: GOV rpm channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(9) S. BUS connection: GOV sw channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(10) S. BUS connection:
Condition on change channel
Select "Cond CH #" in the same way and use the [
/
+] or
[
/
-] key to set the condition change channel of the trans-
mitter.
(2) S. BUS connection: ELE (Elevator) channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(3) S. BUS connection: THR (Throttle) channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(4) S. BUS connection: RUD (Rudder) channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
(5) S. BUS connection: PIT (Pitch) channel
Using the [
/
+] or [
/
-] key to set the correct channel number.
SBUS BASIC screen 1/3
SBUS BASIC screen 2/3
As with the light condition function of the transmitter, you can set
up and use up to ive data of several parameters by switch opera-
tion from the transmitter. By setting the condition switch on the
channel with the AFR function of the transmitter and setting the
point for each light condition with the AFR point curve, you can
switch the condition of CGY760R in conjunction with the light con-
dition switch of the transmitter.
up and use up to ive data of several parameters by switch opera-
tion from the transmitter. By setting the condition switch on the
channel with the AFR function of the transmitter and setting the
point for each light condition with the AFR point curve, you can
switch the condition of CGY760R in conjunction with the light con-
dition switch of the transmitter.
:
:
:
If the "Setup Style" setting of the "SWH BASIC"
menu on page 49 is "F3C", set the aileron (Roll)
gain and the elevator (Pitch) gain on separate
channels. (Gain AIL and Gain ELE display)
menu on page 49 is "F3C", set the aileron (Roll)
gain and the elevator (Pitch) gain on separate
channels. (Gain AIL and Gain ELE display)
F3C
3D