UTC Fire & Security Americas Corporation Inc 723-TCVR ユーザーズマニュアル
4
Setting the Unit Number
2.
Insert the magnet into the nibs on the module cover.
Remove the magnet clip from the module back-plate
and press the magnet clip down over the magnet until it
clicks into place (Figure 7).
Remove the magnet clip from the module back-plate
and press the magnet clip down over the magnet until it
clicks into place (Figure 7).
3.
Connect the normally closed reed switch (in series with
a 2.0K ohm EOL resistor) to the desired panel, HIM, or
SnapCard zone input terminals. The resistor should be
located at the reed switch inside the module housing.
a 2.0K ohm EOL resistor) to the desired panel, HIM, or
SnapCard zone input terminals. The resistor should be
located at the reed switch inside the module housing.
Figure 7. Installing the Optional Reed Switch
Setting the Unit Number
Each bus module connected to the panel must have a differ-
ent unit number set for correct communication.
ent unit number set for correct communication.
Setting the Unit Number on Concord Panels with
Software Versions 1.0–1.6
Software Versions 1.0–1.6
The module can be set to any unit number 0–15, using the
module DIP switches.
module DIP switches.
Note
Do not set the SuperBus 2000 RF Receiver unit num-
ber to 15 if it is installed in a Concord RF system,
since the built-in receiver is factory set to unit number
15 and cannot be changed.
ber to 15 if it is installed in a Concord RF system,
since the built-in receiver is factory set to unit number
15 and cannot be changed.
Locate the DIP switches on the module and set them to the
desired unit number (0–15) before applying power (see Fig-
ure 8).
desired unit number (0–15) before applying power (see Fig-
ure 8).
Figure 8. Unit Number DIP Switch Settings
Setting the Unit Number on Concord Panels with
Software Version 2.0 or Later
Software Version 2.0 or Later
The unit number will be automatically set when powering
up the system. No action is required by the installer.
up the system. No action is required by the installer.
Power Up and Bus Communication
Use the following procedures for powering up the system
and verifying bus communication.
and verifying bus communication.
Note
In order to enter panel program mode to verify unit
numbers, an alphanumeric touchpad must be con-
nected to all Concord panels.
numbers, an alphanumeric touchpad must be con-
nected to all Concord panels.
To power up the panel and receiver module:
1.
Verify that all wiring at the panel, touchpad, and
receiver is correct.
receiver is correct.
2.
Connect the panel backup battery and plug in the panel
AC power transformer.
AC power transformer.
3.
Verify that the receiver module status LED is on.
4.
If desired, enter panel program mode to verify unit
number exists (see panel Installation Instructions for
more information).
number exists (see panel Installation Instructions for
more information).
Note
If the receiver module LED is not on, unplug the panel
AC power transformer, disconnect the backup battery,
and see Table 3 “Troubleshooting”.
AC power transformer, disconnect the backup battery,
and see Table 3 “Troubleshooting”.
9712G12A.DSF
MODULE
BACK-PLATE
BACK-PLATE
MODULE
COVER
COVER
REED
SWITCH
SWITCH
MAGNET
CLIP
CLIP
MAGNET
TO ANY ZONE
INPUT
INPUT
2.0K OHM EOL
RESISTOR (49-467)
RESISTOR (49-467)
1065G05A.DSF
UNIT NUMBER 0
1 2 3 4
ON
UNIT NUMBER 1
1 2 3 4
ON
UNIT NUMBER 2
1 2 3 4
ON
UNIT NUMBER 3
1 2 3 4
ON
UNIT NUMBER 4
1 2 3 4
ON
UNIT NUMBER 5
1 2 3 4
ON
UNIT NUMBER 6
1 2 3 4
ON
UNIT NUMBER 7
1 2 3 4
ON
UNIT NUMBER 8
1 2 3 4
ON
UNIT NUMBER 9
1 2 3 4
ON
UNIT NUMBER 10
1 2 3 4
ON
UNIT NUMBER 11
1 2 3 4
ON
UNIT NUMBER 12
1 2 3 4
ON
UNIT NUMBER 13
1 2 3 4
ON
UNIT NUMBER 14
1 2 3 4
ON
UNIT NUMBER 15--Do not use in Concord RF systems.
1 2 3 4
ON