UTC Fire & Security Americas Corporation Inc 808-UFT ユーザーズマニュアル

2

10. Reattach the circuit board to the UFT base

11. Attach the External Switch (See “Connecting External 

Switch” in this manual)

12. Reattach the UFT cover to the UFT base.

Use a 4”x4” non-metallic electrical box that is at least 1½” 
deep.

In this installation method the UFT is mounted in an electri-
cal box attached to a wall. The magnet is installed in the 
wall and passes through the box.

1.

Determine a suitable location for the UFT.

2.

Mark where the magnet will be installed.

3.

Drill a 3/4” diameter hole 3/4” deep into the stud or 
wall.

4.

Mark where the box will be installed over the magnet.

5.

Mark the box at the location where the magnet will 
enter the box.

6.

Drill a 13/16” hole in the box at the magnet location.

7.

Mark where the UFT will be installed on the box.

8.

Verify the UFT reed switch is properly aligned with the 
magnet hole.

9.

Mount the box using screws or brads making sure to 
align the hole in the box with the hole in the wall or 
stud.

10. Push the magnet, magnet side first, through the hole in 

the box and into the hole in the stud or wall. The top of 
the magnet should be flush with the side of the box.

11. Mount the UFT in the box using velcro strips.

12. Remove the UFT cover by squeezing the cover ends 

firmly to release the tab on the cover from the slot on 
the UFT base.

13. Attach the External Switch (See “Connecting External 

Switch” in this manual)

14. Reattach the UFT cover to the UFT base.

In this installation method the UFT is mounted in an electri-
cal box permanently installed in a wall. The magnet is 
installed in the box.

1.

Determine a suitable location for the UFT.

2.

Mark the box at the location where the magnet will be 
installed.

3.

Drill a 3/4” hole in the box at the magnet location.

4.

Insert the magnet into the hole.

5.

Mark where the UFT will be installed on the box

6.

Verify the UFT reed switch is properly aligned with the 
magnet.

7.

Mount the box in the wall using screws or brads.

8.

Mount the UFT in the box using velcro strips.

9.

Remove the UFT cover by squeezing the cover ends 
firmly to release the tab on the cover from the slot on 
the UFT base.

10. Attach the External Switch (See “Connecting External 

Switch” in this manual)

11. Reattach the UFT cover to the UFT base.

The normally open UFT (60-917) should be connected to a 
normally open external switch. 

❑

Do not use mechanical switches.

❑

Do not use more than 100feet of 18-gauge, stranded or 
solid core wire in any wire run.

❑

Do not use more than 6 feet of untwisted wire in any 
wire run.

❑

Do not run wires parallel to electrical wires. If you 
can’t avoid a parallel wire run, keep at least 18 inches 
away from electrical wiring.

If necessary, you may cross electrical wires at a 90 

degree angle.

1.

Make the connection to the external fire detection 
device. (See your device’s instructions.)

A 4.7 k Ohm EOL resistor must be installed 

at the fire detection device for proper supervision of the 
UFT.

2.

Feed the wire through the hole in the bottom of the 
UFT.

3.

Attach the wire to the terminal block. See Figure 2.

It may be beneficial to feed the wire through the 

hole before mounting the UFT.

The following steps describe the general guidelines for pro-
gramming (learning) a sensor. Refer to the specific panel