UTC Fire & Security Americas Corporation Inc 808-UFT マニュアル

目次

• About this Document

  1
• Product Summary

  1
  • Tools Needed

    1
• Installation

  1
  • General Sensor Installation Guidelines

    1
  • Install on a Wall

    1
    • 1. Determine a suitable location for the UFT.

      1
    • 2. Mark where the magnet will be installed.

      1
    • 3. Drill a 3/4” diameter hole 3/4” deep into the wall.

      1
    • 4. Push the magnet into the hole, magnet side first.

      1
    • 5. Remove the UFT cover by squeezing the cover ends firmly to release the tab on the cover from t...

      1
    • 6. Remove the circuit board from the UFT base by pulling back the plastic tab and lifting the bat...

      1
    • 7. Mark where the UFT will be installed over the magnet. See Figure 1 for acceptable magnet locat...

      1
      • Figure 1. Acceptable magnet locations for a wall mounted UFT.

        1
    • 8. Verify the UFT reed switch is properly aligned with the installed magnet.

      1
    • 9. Mount the UFT base with screws or brads. Use spacers to compensate for metal surfaces or heigh...

      1
    • 10. Reattach the circuit board to the UFT base

      2
    • 11. Attach the External Switch (See “Connecting External Switch” in this manual)

      2
    • 12. Reattach the UFT cover to the UFT base.

      2
  • Install in an Electrical Box

    2
    • Mounting the box on a wall

      2
      • 1. Determine a suitable location for the UFT.

        2
      • 2. Mark where the magnet will be installed.

        2
      • 3. Drill a 3/4” diameter hole 3/4” deep into the stud or wall.

        2
      • 4. Mark where the box will be installed over the magnet.

        2
      • 5. Mark the box at the location where the magnet will enter the box.

        2
      • 6. Drill a 13/16” hole in the box at the magnet location.

        2
      • 7. Mark where the UFT will be installed on the box.

        2
      • 8. Verify the UFT reed switch is properly aligned with the magnet hole.

        2
      • 9. Mount the box using screws or brads making sure to align the hole in the box with the hole in ...

        2
      • 10. Push the magnet, magnet side first, through the hole in the box and into the hole in the stud...

        2
      • 11. Mount the UFT in the box using velcro strips.

        2
      • 12. Remove the UFT cover by squeezing the cover ends firmly to release the tab on the cover from ...

        2
      • 13. Attach the External Switch (See “Connecting External Switch” in this manual)

        2
      • 14. Reattach the UFT cover to the UFT base.

        2
    • Mounting the box in a wall

      2
      • 1. Determine a suitable location for the UFT.

        2
      • 2. Mark the box at the location where the magnet will be installed.

        2
      • 3. Drill a 3/4” hole in the box at the magnet location.

        2
      • 4. Insert the magnet into the hole.

        2
      • 5. Mark where the UFT will be installed on the box

        2
      • 6. Verify the UFT reed switch is properly aligned with the magnet.

        2
      • 7. Mount the box in the wall using screws or brads.

        2
      • 8. Mount the UFT in the box using velcro strips.

        2
      • 9. Remove the UFT cover by squeezing the cover ends firmly to release the tab on the cover from t...

        2
      • 10. Attach the External Switch (See “Connecting External Switch” in this manual)

        2
      • 11. Reattach the UFT cover to the UFT base.

        2
• Connecting External Switch

  2
  • Connection Guidelines

    2
  • Making the Connection

    2
    • 1. Make the connection to the external fire detection device. (See your device’s instructions.)

      2
    • 2. Feed the wire through the hole in the bottom of the UFT.

      2
    • 3. Attach the wire to the terminal block. See Figure 2.

      2
      • Figure 2. UFT component locations.

        2
• Programming

  2
  • 1. Set the panel to program mode.

    3
  • 2. Proceed to the LEARN SENSORS menu.

    3
  • 3. Select the appropriate zone type and zone number assignments.

    3
  • 4. Set the external switch in the alarm condition (open for a normally closed circuit, closed for...

    3
  • 5. Trip the sensors tamper switch by removing the sensor cover.

    3
  • 6. Exit program mode.

    3
  • 7. Place the cover back on the sensor.

    3
• Testing

  3
  • 1. Set the panel to the installer zone test mode.

    3
  • 2. Trip the sensor.

    3
  • 3. The signal strength from the UFT will be displayed on all keypads. It should be 15 or higher f...

    3
• Specifications

  3
• FCC Notice

  4