Volansys Technologies pvt ltd MKW41Z ユーザーズマニュアル
VT-MKW41Z Module Datasheet
Rev 0.4
Confidential
Copyright © 2017 Volansys
Volansys Technologies
Page | 25
The OEM must comply with the FCC labeling requirements. If the module’s label is not
visible when installed, then an additional permanent label must be applied on the outside
of the finished product which states: “Contains transmitter module FCC ID: 2AKNO-
MKW41Z Additionally, the following statement should be included on the label and in
the final product’s user manual: “This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interferences, and (2) this device must accept any interference received,
including interference that may cause undesired operation.”
of the finished product which states: “Contains transmitter module FCC ID: 2AKNO-
MKW41Z Additionally, the following statement should be included on the label and in
the final product’s user manual: “This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interferences, and (2) this device must accept any interference received,
including interference that may cause undesired operation.”
The module is limited to installation in mobile or fixed applications. Separate approval is
required for all other operating configurations, including portable configuration with re
spect to Part 2.1093 and different antenna configurations.
spect to Part 2.1093 and different antenna configurations.
module or modules can only be used without additional authorizations if they have been
tested and granted under the same intended end‐se operational conditions, including
simultaneous transmission operations. When they have not been tested and granted in
this manner, additional testing and/or FCC application filing may be required. The most
straightforward approach to address additional testing conditions is to have the grantee
responsible for the certification of at least one of the modules submit a permissive change
application.When having a module grantee file a permissive change is not practical or
feasible, the following guidance provides some additional options for host manufacturers.
Integrations using modules where additional testing and/or FCC application filing(s) may
be required are: (A) a module used in devices requiring additional RF exposure compliance
information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not
meeting all of the module requirements; and (C) simultaneous transmissions for
independent collocated transmitters not previously granted together.
simultaneous transmission operations. When they have not been tested and granted in
this manner, additional testing and/or FCC application filing may be required. The most
straightforward approach to address additional testing conditions is to have the grantee
responsible for the certification of at least one of the modules submit a permissive change
application.When having a module grantee file a permissive change is not practical or
feasible, the following guidance provides some additional options for host manufacturers.
Integrations using modules where additional testing and/or FCC application filing(s) may
be required are: (A) a module used in devices requiring additional RF exposure compliance
information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not
meeting all of the module requirements; and (C) simultaneous transmissions for
independent collocated transmitters not previously granted together.
This Module is full modular approval; it is limited to OEM installation ONLY.
Integration into devices that are directly or indirectly connected to AC lines must add with Class II
Permissive Change.
(OEM) Integrator must assure compliance of the entire end product include the integrated
Module.
Additional measurements (15B) and/or equipment authorizations (e.g Verification) may need to
be addressed depending on co-location or simultaneous transmission issues if applicable.
(OEM) Integrator is reminded to assure that these installation instructions will not be made
available to the end user of the final host device.
Integration into devices that are directly or indirectly connected to AC lines must add with Class II
Permissive Change.
(OEM) Integrator must assure compliance of the entire end product include the integrated
Module.
Additional measurements (15B) and/or equipment authorizations (e.g Verification) may need to
be addressed depending on co-location or simultaneous transmission issues if applicable.
(OEM) Integrator is reminded to assure that these installation instructions will not be made
available to the end user of the final host device.
9.4 IC Statement
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to
the following two conditions: (1) This device may not cause interference, and (2) This device must
accept any interference, including interference that may cause undesired operation of the device.
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that
the following two conditions: (1) This device may not cause interference, and (2) This device must
accept any interference, including interference that may cause undesired operation of the device.
This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that