Motorola Solutions Inc. 89FT7634 ユーザーズマニュアル
PMP 400/430 and PTP 200 Series
Canopy User Guide
Supplement
Issue 4 0 – DRAFT 6 November 2009
Page 38 of 64
4.4.1
Background and Operation
The modules use region-specific DFS based on the “Region Code” selected on the module’s
“Configuration => General” page. By directing installers and technicians to set the Region Code
correctly, the operator gains confidence the module is operating according to national or regional
regulations without having to deal with the details for each region.
“Configuration => General” page. By directing installers and technicians to set the Region Code
correctly, the operator gains confidence the module is operating according to national or regional
regulations without having to deal with the details for each region.
Available “Region Codes” include Other, United States, Canada, Europe, Brazil, Russia, and
Australia. Operators in regions or countries not listed and with requirements aligned with one of
the listed countries should set the Region Code to that country. Operators in regions or countries
with no requirements for DFS should use the “Other” Region Code.
Australia. Operators in regions or countries not listed and with requirements aligned with one of
the listed countries should set the Region Code to that country. Operators in regions or countries
with no requirements for DFS should use the “Other” Region Code.
New APs and BHMs from the factory will show a Region Code of “None”, and will not transmit
until the Region Code is set to a value other than “None”.
until the Region Code is set to a value other than “None”.
Canada, United States and Europe have requirements to avoid certain frequencies used by some
weather radar. To meet this requirement, modules set to a Region Code of Canada, United
States or Europe will display the center channel frequencies shown in
weather radar. To meet this requirement, modules set to a Region Code of Canada, United
States or Europe will display the center channel frequencies shown in
on page
AP’s and BHM’s Carrier Frequency pop-up and on the SM’s and BHS’s Frequency Scan
Selection List.
Selection List.
including whether DFS is active on the AP/BHM, SM/BHS, which DFS regulation apply, and any
channel restrictions. DFS does not apply to 4.9 GHz.
channel restrictions. DFS does not apply to 4.9 GHz.
Table 12: 5.4 / 5.8 GHz DFS Operation based on Region Code
Region Code
1
Frequency
AP
SM
Center Channel
Frequencies Available
2
(MHz)
United States
5.4 GHz
FCC/IC DFS
3
No effect
5480 - 5710
5.8 GHz
No effect
No effect
5730 - 5845
Canada
5.4 GHz
FCC/IC DFS
3
No effect
5480 – 5595, 5655 - 5710
5.8 GHz
No effect
No effect
5730 - 5845
Europe
5.4 GHz
ETSI DFS
4
ETSI DFS
5475 - 5595, 5655 - 5715
5.8 GHz
ETSI DFS
5
ETSI DFS
5730 - 5870
Brazil
5.4 GHz
ETSI DFS
No effect
5475 - 5715
5.8 GHz
No effect
No effect
5730 - 5845
Australia
5.4 GHz
FCC/IC DFS
No effect
5480 – 5595, 5655 - 5710
5.8 GHz
No effect
No effect
5730 - 5845
Russia
5.4 GHz
NA
NA
5480 - 5710
5.8 GHz
NA
NA
5730 - 5845
Other
5.4 GHz
No effect
No effect
5480 - 5710
5.8 GHz
No effect
No effect
5730 - 5870
1. In all cases set the Region Code to the region you are in and the equipment will
provide DFS consistent with that region’s regulations. For countries or regions
not listed, use a Region Code that provides DFS functionality and channels
not listed, use a Region Code that provides DFS functionality and channels