Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. SOYAL TECHNOLOGY CO. LTD.
  4. AR-837
  5. ユーザーズマニュアル

SOYAL TECHNOLOGY CO. LTD. AR-837 ユーザーズマニュアル

ダウンロード
ページ / 9
SOYAL
ACCESS CONTROL SYSTEM
®
AR-837
V140217
   
H. Arming Password
J. Duress Code
K. Terminal Port
I. Arming Delay Time
Access programming mode →  
   Parameters[1] →     Arming PWD → Input 4-digit PIN (0001~9999; Default: 1234) → Succeeded  
Or via 701Server and set it on  AR-829E  screen
3
8
Or via 701Server to set it on  AR-829E-V5  screen
※
Duress Code is only available in networking mode. It will substitute a personal pin code and send the message of Duress to computer as a    
    warning signal.
Access programming mode →  
   Parameters[2] →     Duress Code → 4 sets (select one) → Input 4-digit PIN (0001~9999) → Succeeded  
4
7
Access programming mode →  
   Tools →     Terminal Port → 0:Lift ; 1:Host ; 2:LED ; 3:PRN (default value:1) → Baud Selection 
(default value:9600) → Succeeded  
5
4
L. Setting up the alarm / arming
Conditions:
1. Arming enabled
2.Alarm system connected
Situations:
1. Door is open overtime: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position is abnormal: Happening when power is off and then on again, besides, reader was on arming before power went off.
Enable/Disable the arming status:
Standby Mode
Access Programming mode
Card only
Card or PIN
Card and PIN
Open the door
Present the tag to reader → 
Input 
4-digit arming PWD →
Input user address → Input 
4-digit individual PWD →      → 
Input 4-digit arming PWD →
Present the tag to reader → 
Input 
4-digit individual PWD →      → 
Input 4-digit arming PWD →
Enable: Access programming mode →     Quit & Arming
7
Disable: Access programming mode →     Quit
6
No open the door
     → 
Input 4-digit arming PWD 
→ 
Present the tag to reader
Access programming mode →     Parameters[1] →     ArmingDelayTm → 
Enter armed sta. Delay time(Sec), Range:000~255；
Armed pulse out-put time (10ms) ,Range：000~255 → Succeeded  
3
7
※ 
[Use FP] can substitute for [Induct valid card].
F. Adding / Deleting Fingerprint 
Adding
Access programming mode →  
   User Setting →     Enroll FP → Key in 5-digit user address →1 or 2 different fingers on the sensor lens → Succeeded
P.S. The AR-837EF needs to collect twice for each fingerprint.
2
6
Deleting
Access programming mode →  
   User Setting →     Delete FP → Key in 5-digit user address → Succeeded
P.S. If you want to delete all users’ FP, key in 
99999
2
7
#
G. Access Mode
Access programming mode →  
   User Setting 
→     
Access Mode 
→ 
Key in 5-digit user address (00000~08999) 
→ 
0: Invalid; 1:Card; 2: Card or PIN; 3: Card and PIN 
(
837EF: → Finger Identify: 0: Must ; 1: Ignore )
→ 
Succeeded  
2
2
Access Mode
Finger Identify (837EF Only)
Result  (837EF Only)
Hardware 701Client
Hardware
701Client
0:Invalid
0: Must
 
       Just fingerprint
       Just card control
 Invalid User
1: Ignore
       Just fingerprint
       Just card control
1:Card
0: Must
       Just fingerprint
       Just card control
 
Finger+Card
1: Ignore
       Just fingerprint
       Just card control
 1. Card Only
 2. Finger Only
2:Card or PIN
0: Must
       Just fingerprint
       Just card control
 1. Finger+Card
 2. Finger+PIN
 3. Card+Finger+PIN
 4. Card+Finger+Card
 5. PIN+Finger+PIN
 6. PIN+Finger+Card
1: Ignore
       Just fingerprint
       Just card control
 1. Card Only
 2. PIN Only
 3. Finger Only
3:Card and PIN
0: Must
       Just fingerprint
       Just card control
 Finger+Card+PIN
1: Ignore
       Just fingerprint
       Just card control
 1. Card+PIN
 2. Finger+PIN