Otodata Wireless Network Inc. C008TR900 ユーザーズマニュアル

- DBALL 2
- Autostart Pager 
   Port 

(HRN-RS-1) 

- ASD-200
- 4X10

- EVO-ALL

- AKX
- iDatastart
- EVO-ONE
- ADS-AL-CA
- Compustar
- DSE (INTV1) 

+12V Ba

tt

ery 

Gr

ound 

Da

ta

 

Da

ta

 

+ Ignition

 

Horn

 

Antenna: Cord length 9 feet

Installation: Place 
antenna 3 inches (minimum) 
from any obstructions

Orientation: Vertical; antenna 
facing downwards (as seen in 
diagram)

CAR STARTER

or BYPASS

RF KIT INPUT

 (3)

a.  Connect the C5040 unit
b.  Wait for the start up sequence
c.  The module is in programming mode  

by default if not already programmed

d.  The blue LED will blink according to the 

selected protocol:

  i. ADS 

(default)

  ii. Fortin

  iii. Xpresskit

  iv. Smart Start 

(PolarStart version  

  H7.0 V6.0 +)

  v.  Polarstart Pager Legacy

  vi. Trigger Start (-)
e.  Briefly press the button to change  

the protocol

f.   Press and hold the button for 2 seconds 

to save the selected protocol

g. For Fortin only (learning procedure):
  i.   Enter the transmitter learning  

  mode by following the remote  

  starter instructions

  ii.  Once the transmitter learning mode  

  is entered, the Blue LED will start  

  blinking on the C5040 unit. Briefly  

  press and release the programming  

  button to send a LOCK command to  

  the remote starter

  iii.  The C5040 unit should now be  

  registered with the remote car starter

iv.  Exit the remote learning mode of  

  the remote car starter

h.  The C5040 unit is now in “operation” 

mode.

a.  Disconnect the C5040 unit
b.  Turn ignition ON
c.  Connect the C5040 unit
d.  Wait for the start up sequence
e. The C5040 will now be in “Installer 

Mode” for 15 seconds and the purple  

LED will blink slowly

f.   During this time, turn ignition OFF to 

send an UNLOCK command to confirm 

programming

g.  The C5040 unit is now in “operation” 

mode. 

Action / Event

LED Display

Red, Green and Blue LED  
are ON sequentially

Fast blink of the Green LED 
during 1 second

Fast blink of the Red LED 
during 1 second

Fast blink of the Orange LED 
during 2 seconds

a.  Install the smartphone app
b.  Create customer login 

(if one does not already exist)

c.  Go to “Add vehicle”
d.  Enter 

e.  Registration completed 

Move the vehicle to an 

and turn ignition off to allow the system to 

register in the network.

“Pit-Stop” mode:
1.  While your vehicle is parked and 

your motor is idling, press and 

hold the button for 2 seconds (the 

green LED will blink 2 times). The 

C5040 unit will send a START 

command to the car starter while 

the motor is running. This will 

activate the “Pit-Stop” mode.

2.   Pull out the key and get out of the 

vehicle (the motor still running).

(1) Must be used with EVO-ALL, ADS-AL-CA or DBALL 2

(2) One-way only (no feedback on start troubles)

(3) Optional

C5040/MS2

TELEMATICS COMMUNICATOR

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Changes 
or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Warning RF Exposure Compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and 
must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

This system must be installed 

by a professional.