Kum Oh Electronics Co. Ltd. KG-SMART-B01 ユーザーズマニュアル

Electric outlet

h

Click Internet on the smartphone that you are going to connect to the kit(  a  ) and
access ‘retailsamsung.com’. (To access  with Internet, the Wifi is connected.)
Search for S pen on the website.

NFC chip

e

e

a

Remove the

protective film

After tagging, press 'Yes' when the NFC connection confirmation message window
appears. When the device is connected normally, “NFC is detected”, “Pairing
Succeed(Button1)”, “Pairing Succeed(Button2)” and “Service is launched” will
appear and then disappear on the screen in sequential order.

It may be different from the

actual image of the phone.

Button cover

When the button is pressed for the first time, the full screen guide information is
displayed, this will be closed when you swipe up or press the NEXT and OK buttons.

Maintenance kit

S035_EN1709_R01

▶Before installation - Checking the part  

h

i

f1

f2

f3

f4

a

b

e

c

d

m1

m2

m3

m4

m5

m6

■ Maintenance kit:

      Use if the product needs to be reinstalled.

※ The standard adaptor for

Do not remove the cable winding prevention
sheet before the security cable has been fully
connected to the smartphone. If the security
cable goes inside the kit after it is removed, 
it will be difficult to install it.

m4

g

Connect all buttons( e    ) to the connector inside the Kit( a    ) where the button
cover has been removed.

e

e

Align the position of 1(S Pen) and 2(Camera) inside the Kit(   a  ) with the position of
button as shown in the figure and insert them so that the certification label is shown
at the top. 

※Check the number on the label for installation to ensure that you do not

change the button position.

Insert the button cover and assemble it again using the screw separated from       
and the screw driver(   i   ).

Button cover

Turn

clockwise

i

Enable the Bluetooth and NFC (basic mode) function on the smartphone. 
Place the smartphone on top of NFC chip of No. 1 (S Pen) button for tagging as
shown in the figure below.

※ Both of the two buttons will be connected by a single NFC tagging.

a

i

※ If the Samsung Retail Mode is not installed on Note8, download and install the Note8 Retail mode package through ‘PVI’
    or ‘retailsamsung.com’. Without Samsung Retail Mode, normal Kit setting is unavailable.

▶When replace the display smartphone

1. Turn off the Kit and the control box.
2. Remove the charging & security cable connector previously connected to the smartphone and turn off the smartphone.
    (Refer to the back page of this manual for information on how to separate the connector.)
3. Install a new smartphone by following the instructions in this manual.

※If a new smartphone is installed, the previous display smartphone will not be connected.

If you press the S PEN button, please check Live Message Experience video is
played.

Using the screwdriver(  i    ), remove the screw holding the button cover on the bottom
surface of the Kit(  a   ).

œTake care not to lose the disconnected screw.

i

e

a

a

a

h

b

Power Terminal

Connect the exclusive adaptor connector(  h  ) for the Kit to the the power terminal
on the bottom surface of the Kit(  a   ) and organize the cable along the the cable
guide as shown in the figure. Connect the exclusive adaptor(  h  ) for the Kit to an
electric outlet. 

※Please use the supplied power adaptor in this package. Otherwise, the device
   may damaged. 

a

h

h

h

Button cover

Switch ON

 Open the switch cover on the back of Kit(  a   ) and check whether the switch is ‘ON’.

※ If it is in ‘OFF’ position, change its position to ‘ON’.

a

Switch cover

a

m6

m6

If the price tag needs to be replaced, attach the ‘pull tape(       )’ included in the 
maintenance kit to the price tag window(       ) as shown in the figure below, hold 
and pull the handle. Remove the price tag in the same way. 

m6

Remove the protective film from all double-sided adhesive tapes at the bottom
surface of the Kit(   a  ).  Firmly attach the Kit(  a   )  to an appropriate position on
the table for display.

Table

a

a

a

Price tag

Price tag

groove

Put the price tag in the price tag groove on the first page of the Flip Book and cover
the price tag window(       ) to the groove.

※The price tag is not included in this package. Please print the price tag locally and
    put it on tag groove. (Size of price tag : Width - 33.5mm/ Height - 18.5mm)

g

g

g

Check whether the Optical 2x Zoom introduction video is played back when the
Camera button is pressed an odd number of times and if Live Focus introduction
video is played back when the Camera button is pressed an even number of times.

g

Turn

counter-clockwise

i

Execute “Button Launcher” by touching it and check whether pairing has been
 completed normally.
        is displayed when pairing with the smart button has been completed normally.

Select, download and install [Global] Galaxy Note8 S pen - Camera Kit Experience
app Patch.

   
 

e

1. After removing the protective film from the double-sided adhesive tape, preserve the tape so that it doesn't get dirty.
    

If touching the tape with a hand or foreign materials get on it, its adhesive strength can be significantly deteriorated.

2. The adhesive tape will have full adhesive strength after the 24 hours from its placement. Please do not use the products right after its placement.

PRESS IT EVENLY 

30 SECONDS MORE!