Kum Oh Electronics Co. Ltd. KG-SMART-B01 ユーザーズマニュアル

Remove the winding

prevention sheet 

Mounting groove

c

c

S-Pen mounting hole

Turn

counter-clockwise

▶Safety warning

▶How to separate the charging & security cable and S-Pen security wire

▶Information

Turn OFF the control box, separate the security cable(      ) and loosen the screw
assembled to the charging & security cable connector(      ).

※In case of SES/SIS Preview Kit, separate all 2 charging & security cable connectors.
※If you separate the cable(       ) without turning off the control box, an alarm will sound.

Detach the bonded part at the back of connector(      ) using a remover(      ), and
separate the connector.

※Since the remover head is sharp, make sure to wear gloves and use it carefully.

※ Before separating the charging & security cable, make sure to turn OFF the control box.

※Turn OFF the switch.

Control box

b

m5

b

b

Separate the locking clip(      ) by using a gimlet.

※The gimlet or the pointed tool is not included in this package.

Take the product apart in the reverse order of its assembly. 

※Be careful not to lose any separated part.

Gimlet or

pointed tool

S-Pen

f4

f4

c

c

c

c

f2

f3

① Assemble the bottom plate of the security lid(      ) with the top plate of the security lid(      ).
② Align the security holder(      ) with the locking clip insertion hole of the combined security lid, and assemble the security holder(      ).
③ Insert the security holder(      ) into the end of the security lid, and insert the locking clip(      ) into the locking clip insertion hole.

Combined

security lid

S-Pen head

① Before installing the security wire for S-Pen, assemble the S-Pen by extruding the S-Pen head as shown in the figure.
② Place the head of the S-Pen into the groove on the bottom plate of the security lid(      ).
   

※Insert it in such a way that the surface with no SAMSUNG logo becomes the top side, as shown in the figure.

③ Place the security wire molding(      ) into the bottom plate of the security lid(      ).

Completed assembled

Security wire

Locking clip

insertion hole

Locking clip

insertion hole

Connect the charging & security cable connector(      ) to USB port on the
control box, and turn ON the control box.

※In case of SES/SIS Preview Kit, connect all 2 charging & security cable connectors.
※After turning ON the control box, check if LED of the control box is ON.

Mount S-Pen assembled with the security wire on S-Pen mounting hole on the
Kit.

※Mount it in the way that the SAMSUNG logo of S-Pen is shown in front.

Control box

b

b

※Turn ON the switch.

f1

f1

f1

f1

f2

f2

d

d

f2

f2

f2

f3

f3

f4

f4

※Assemble in such a way that the surface

with no SAMSUNG logo becomes the top side,

as shown in the figure.

When connector(   c  ) installation is complete, remove the winding prevention sheet
by spreading it in the opposite directions and mount the device on the mounting
groove.

O

c

Adjust the surface where the connector(      ) is attached to make it horizontal as
shown in the figure, and then press it so the whole surface is attached evenly.

c

c

a

Remove the

protective film

c

Remove the protective film from the double – sided adhesive tape of connector.
Rotate the back of the universal sensor cable connector(      ) to make it horizontal
with the smartphone.

c

After attaching the connector(      ), press and hold the whole attached surface
evenly and firmly for more than 30 seconds to attach it. Reassemble the screw
which is released during assemble process       with supplied  screw driver(      ). 

c

c

Turn

clockwise

PRESS IT EVENLY 

30 SECONDS MORE!

c

c

c

i

i

m5

f1

i

Turn

counter-clockwise

c

c

Pull the connector to a length that will allow you to connect the charging & security
cable connector(      ).

Release the back screw of charging & security cable connector(      ) with supplied
screw driver(      ), and connected the connector(      ) with smartphone.

c

c

c

i

i

▶Trouble Shooting

Execute "Button

Launcher" on the

smartphone.

Try pairing with

the smart button

through NFC

tagging

If pairing is not

made normally, 

check if the power

connection to

the smart button

is normal.

When the "Disconnected"

image is displayed, 

it is the Bluetooth

pairing problem.

Disconnected Connected

This error message is displayed when a video file for

operating contents does not exist in the device.

Confirm that video files are normally distributed

to the relevant device through RMS. 

※The specifications and design of the product may be modified without prior notice to improve
    product performance.

Warranty Period

 Item

 One year from shipment date.

Manufacturer

KUMOH Electronics Co.,Ltd

Address

  35, Gilju-ro 444beon-gil,

Bucheon-si, Gyeonggi-do (Seoul 14556 Korea)

info@kumohec.co.kr

82-32-662-2000 / 82-32-662-9312

■ Limited warranty

■ Manufacturer Information

Tel / Fax 

E-mail

‡Do not expose the product to fire or other electric heaters!
  - This creates the risk of fire or damage to the product.
‡Do not disassemble, repair, or remodel the product!
  - This creates the risk of injury.
  - Please call the service center when repair is necessary.
‡Do not forcibly bend or pull the wire!
  - This creates the risk of damage to the product or injury to the user.
‡When the wire is disconnected or breaks away, do not touch the wire with bare hands, but always wear
  protective hand gloves!
  - The disconnected part of the wire is sharp, thus, may cause injury.  
‡Do not use the wire for purposes other than as a security alarm device, and do not allow access to children!
  - Winding the wire around your neck or body may result in death or serious injury.
‡Do not touch the wire when there is lightning and thunder!
  - This creates the risk of electric shock.
‡The cable is a consumable product, so free repair service is not provided even within the warranty period in
   the event of damage or failure due to excessive use or intentional misuse.

SES/SIS S Pen & Camera

Launch Kit