JVC TH-C20 ユーザーズマニュアル
10
To obtain the best possible sound from this system, you need to
place all the speakers except the subwoofer at the same distance
from the listening position.
place all the speakers except the subwoofer at the same distance
from the listening position.
If your speakers cannot be placed at the same distance from the
listening position
You can adjust the delay time of the speakers. See “Delay menu
(DELAY)” on page 34.
listening position
You can adjust the delay time of the speakers. See “Delay menu
(DELAY)” on page 34.
NOTE
• Place the satellite speakers on a flat and level surface.
• The front and center speakers are magnetically shielded to avoid color
• The front and center speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, they may cause
color distortions. So, pay attention to the following when installing
the speakers.
– When placing the speakers near a TV set, turn off the TV’s main
color distortions. So, pay attention to the following when installing
the speakers.
– When placing the speakers near a TV set, turn off the TV’s main
power switch or unplug it before installing the speakers. Then wait
at least 30 minutes before turning on the TV’s main power switch
again.
at least 30 minutes before turning on the TV’s main power switch
again.
Some TVs may still be affected even though you have followed the
above. If this happens, move the speakers away from the TV.
above. If this happens, move the speakers away from the TV.
• The surround speakers are not magnetically shielded.
If they are located nearby the TV or monitor, it will probably cause
color distortion on the screen. To avoid this, do not place the speakers
nearby the TV or monitor.
color distortion on the screen. To avoid this, do not place the speakers
nearby the TV or monitor.
• Be sure to place the powered subwoofer to the TV’s right. If you place
the powered subwoofer to the TV’s left, keep sufficient distance
between them to prevent the TV screen from appearing mottled.
between them to prevent the TV screen from appearing mottled.
• You can get better picture quality in the order — Component
video > S-video > Composite video.
• Distortion of picture may occur when connecting to the TV via a
VCR, or to a TV with a built-in VCR.
• You need to set “MONITOR TYPE” in the PICTURE menu
correctly according to the aspect ratio of your TV. (See page 34.)
7 To connect a TV equipped with the component video input
jacks
• If your TV supports progressive video input, you can enjoy a high
quality picture by setting the progressive scan mode to active.
(See page 16.)
(See page 16.)
NOTE
• If the component video input jacks of your TV are of the BNC type,
use a plug adapter (not supplied) to convert the pin plugs to BNC
plugs.
plugs.
• The component video signals can be output only when you select
DVD or USB MEMORY as the source to play. (See page 15.)
7 To connect a TV equipped with the composite or S-video jacks
Speaker layout
Front right
speaker
speaker
Center speaker
Powered
subwoofer
subwoofer
Surround left
speaker
Surround right
speaker
speaker
Front left
speaker
Connecting a TV
Connecting the powered
subwoofer
subwoofer
Center unit
To component
video input
TV
Component video cord (not supplied)
Composite video cord (supplied)
To composite
video input
video input
S-video cord
(not supplied)
(not supplied)
TV
To S-video input
Center unit
or
Align the 5 marks.
Powered
subwoofer
System cord
(supplied)
(supplied)
Center unit
Align the 5 marks.
Align the 5 marks.
Connections
Do not connect the power cord until all other connections have been made.
TH-C20-30[JC]5.book Page 10 Thursday, January 12, 2006 11:29 AM