Superchips Inc. Car Stereo System 1715 maz ユーザーズマニュアル

 
 

Page 11 of 16

  

Form 0129L 03/29/07                                                                                            

 Superchips Inc

Superchips Inc.  

1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 

Superchip & Superchips are registered trademarks of Superchips, Inc. 

 

 

 

 

After the present program has been erased, the MAX MicroTuner will blink the following 
message: 

 

 

The bottom line of the display shows the programming progress.  

The programming sequence is now complete. Once the programming sequence has been 
successfully accomplished on a vehicle, the MAX MicroTuner becomes LOCKED to that  
vehicle. The MAX MicroTuner may not be used to tune any other vehicle. The MAX 
MicroTuner may be used on other Ford vehicles as a DTC Reader. 

 

When the programming sequence is completed the MAX MicroTuner beeps and will display: 

 

 

The MAX MicroTuner is testing to see if the Passive Anti-Theft System is active. If PATS is 
active the MAX MicroTuner beeps and displays the message: 

 

 

If Returning to Stock, and PATS is not active, the MAX MicroTuner automatically clears the           
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages: 

 

then 

 

 

then 

then 

 

Turn the ignition OFF and remove the cable from the diagnostic port. 

 

The  Return to Stock Sequence is used to reprogram a vehicle previously tuned with the 
Superchips MAX MicroTuner with its original stock tuning. Follow the steps described in 
Connecting the Superchips MAX MicroTuner to your vehicle in section 1. Following the 
typical start up messages, if the MAX MicroTuner has been previously used to program a 
vehicle, the MAX MicroTuner will beep and display: 

 

 

This indicates the MAX MicroTuner has been previously used to program a vehicle. It 
should not be used to program another vehicle. The MAX MicroTuner will continue to 
operate normally on the original vehicle. 

 

After establishing communications, the MAX MicroTuner will display the following message: 

If ‘NO’ is pressed, the

 

MAX MicroTuner will return to Installing the Superchips 

Performance Program at Step 5 above. 

 
 

Page 12 of 16

  

Form 0129L 03/29/07                                                                                            

 Superchips Inc

Superchips Inc.  

1790 East Airport Blvd., Sanford, FL. 32773  (407) 585-7000  http://www.Superchips.com 

Superchip & Superchips are registered trademarks of Superchips, Inc. 

 

 

 

 

If the ‘YES’ key is pressed it will beep once and display the following message: 

 

 

Turn the ignition to the OFF position and press the ‘>’ key on the keypad.  

 

The MAX MicroTuner will beep and blink the following message for approximately 6 
seconds: 

 

 

After initialization is complete, the MAX MicroTuner will beep and display the message: 

 

 

Turn the ignition to the ON position. The MAX MicroTuner will beep and display the 
following messages: 

 

then 

 

then 

 

Press ‘>’. The MAX MicroTuner will beep once and erase the present program. The MAX 
MicroTuner will blink the following message: 

 

 

After the program has been erased, the MAX MicroTuner will blink the following message: 

 

 

The bottom line of the display shows the programming progress.  

 

When the programming sequence is completed the MAX MicroTuner beeps and will display: 

 

 

The MAX MicroTuner is testing to see if the Passive Anti-Theft System is active. If PATS is 
active the MAX MicroTuner beeps and displays the message: 

 

 

If Returning to Stock, and PATS is not active, the MAX MicroTuner automatically clears the           
vehicle DTCs. The MAX MicroTuner Beeps and displays the following messages: 

 

then 

 

 then

then 

 

 

Turn the ignition OFF and remove the MAX MicroTuner cable.