Sterling Home Theater Server XXX10-80 ユーザーズマニュアル
10-Pump, 80-Station Controller Chapter 6: Configurable Settings
66
Name Description
Options
Default
Every n loads
Number of conveying cycles between filter
cleanings.
Adjust this setting based on experience. The
more dust and debris in your material line, the
smaller this number needs to be.
cleanings.
Adjust this setting based on experience. The
more dust and debris in your material line, the
smaller this number needs to be.
1–99 5
# pulses
Number of pulses of compressed air sent
through the station’s filter during cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
through the station’s filter during cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
1–99 5
On time
Number of seconds that the each air pulse lasts
during filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
during filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
0.1–99.9 sec. 1.0 sec.
Off time
Number of seconds between air pulses during
filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
filter cleaning.
If blowback is not working as desired, the
service department may ask you to change this
setting.
0.1–99.9 sec. 1.0 sec.
Slide gate
When this option is enabled, the controller
opens the slide gate between the station and
the receiver during the dump delay and during
blowback.
Enable this option if and only if the station has a
slide gate instead of a flapper and demand
switch.
opens the slide gate between the station and
the receiver during the dump delay and during
blowback.
Enable this option if and only if the station has a
slide gate instead of a flapper and demand
switch.
disabled,
enabled
enabled
disabled
Purge
When enabled, this option allows the system to
empty the material line completely after every
convey to this station. The station’s pump
continues to draw without picking up material for
an extra period of time after conveying is
finished.
Enable this option if and only if you are using a
purge valve for this station. This option cannot
be used with a volume-fill station.
empty the material line completely after every
convey to this station. The station’s pump
continues to draw without picking up material for
an extra period of time after conveying is
finished.
Enable this option if and only if you are using a
purge valve for this station. This option cannot
be used with a volume-fill station.
disabled,
enabled
enabled
disabled
Purge duration
Number of seconds allowed for purging. The
station’s vacuum valve remains open for the
convey time plus this time.
Adjust this setting to the amount of time
required for material to travel from the pickup
point (purge valve) to the station.
station’s vacuum valve remains open for the
convey time plus this time.
Adjust this setting to the amount of time
required for material to travel from the pickup
point (purge valve) to the station.
0–999 sec.
20 sec.
Purge valve
Number (address) for the purge valve used with
this station.
Set this to match the number (address) for the
purge valve that services this station. If another
station has the purge valve that services this
station, enter the number of that station (range:
1–50). If a central purge valve services this
station, enter the number (address) of that valve
(range: 51–154).
this station.
Set this to match the number (address) for the
purge valve that services this station. If another
station has the purge valve that services this
station, enter the number of that station (range:
1–50). If a central purge valve services this
station, enter the number (address) of that valve
(range: 51–154).
1–154
0 (= not
assigned)
assigned)
Material set to n
Number for the material line that should be
connected to this station.
connected to this station.
0 –150
0 (= not
assigned)
assigned)