DeWALT JT360 取り扱いマニュアル
25 - English
REMOVING DUST CHUTE COVER
The dust chute cover (A) Fig. 75, can be removed, for
cleaning purposes, by removing the two wing screws
(B).
cleaning purposes, by removing the two wing screws
(B).
Make certain the machine is
disconnected from the power source before removing
the dust chute cover. The dust chute cover (A) must
always be assembled to the dust chute during
operation.
the dust chute cover. The dust chute cover (A) must
always be assembled to the dust chute during
operation.
B
After considerable use, the knives will become dull and it will not be possible to do accurate work. Unless badly
damaged by running into metal or other hard material, the knives may be sharpened as follows:
damaged by running into metal or other hard material, the knives may be sharpened as follows:
WHETTING KNIVES
Disconnect machine from power
source.
source.
Use a fine carborundum stone, cover it partly with paper
as indicated in Fig. 74 to avoid marking the table. Lay
the stone on the infeed table, lower the table and turn
the cutterhead forward until the stone lies flat on the
bevel of the knife as shown. Hold the cutterhead from
turning, and whet the beveled edge of the knife, stroking
lengthwise by sliding the stone back and forth across the
table. Do the same amount of whetting on each of the
three knives.
as indicated in Fig. 74 to avoid marking the table. Lay
the stone on the infeed table, lower the table and turn
the cutterhead forward until the stone lies flat on the
bevel of the knife as shown. Hold the cutterhead from
turning, and whet the beveled edge of the knife, stroking
lengthwise by sliding the stone back and forth across the
table. Do the same amount of whetting on each of the
three knives.
OILSTONE PARTLY
COVERED WITH PAPER
COVERED WITH PAPER
IN-FEED TABLE
OUT-FEED
TABLE
CUTTER
WHETTING KNIVES
MAINTENANCE
KEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth.
NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the
outlet. Also, check for blown fuses or open circuit breakers in the line.
outlet. Also, check for blown fuses or open circuit breakers in the line.
LUBRICATION & RUST PROTECTION
Apply household floor paste wax to the machine table, extension table or other work surface weekly. Or use a commercially
available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.
To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand
Pad, a can of WD-40® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad.
Degrease the table, then apply the protective product as described above.
available protective product designed for this purpose. Follow the manufacturer’s instructions for use and safety.
To clean cast iron tables of rust, you will need the following materials: a sheet of medium Scotch-Brite™ Blending Hand
Pad, a can of WD-40® and a can of degreaser. Apply the WD-40 and polish the table surface with the Scotch-Brite pad.
Degrease the table, then apply the protective product as described above.
SERVICE
Fig. 74
Fig.75
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our website at servicenet.deltamachinery.com. You
can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to
receive personalized support from highly-trained technicians.
can also order parts from your nearest factory-owned branch, or by calling our Customer Care Center at 1-800-223-7278 to
receive personalized support from highly-trained technicians.