DeLonghi PrimaDonna Exclusive ESAM 6900.M 取り扱いマニュアル

15

pipe and stirrer are already in place. Do not exceed the 
MAX level marked on the carafe. Increase or reduce the 
quantity of hot chocolate powder according to taste.  

•  To use water instead of milk, follow the instructions for

milk.  

•  To prepare hot chocolate correctly, first pour the milk or

water  into the funnel, then add the hot chocolate or cocoa 
powder as shown on the hot chocolate carafe lid.  

5.  Close the lid (fig. 22).
6.  Attach the carafe to the nozzle and push as far as it will go  

(fig. 23). The machine emits a beep (if the beep function 
is enabled). 

7.  Press the CHOCOLATE icon  (B12).
8.  Select one or two cups (

 - 

) by pressing the 

corresponding icon.  

8.  Press the + or - icon to select the required density: 
  

  If the hot chocolate powder used does not contain 

thickener, there will be any change adjusting the density.

9.  Press the CHOCOLATE icon to start making hot chocolate 

(fig. 24). The appliance starts mixing the drink and then 
delivers steam to heat it.  

Once the coffee has been made, the appliance prepares for use 
again.  The chocolate is ready to be poured into the cup. 

While making the chocolate, the carafe and lid become very 
hot. Hold by the handle only to remove the carafe and pour the 
chocolate. 
The chocolate is ready to be poured into the cup. 

•  To interrupt making the chocolate, press the CHOCOLATE 

icon again or the STOP icon. 

. 

While making the hot chocolate, it is normal for steam to 
come out of the holes in the chocolate carafe lid.  

•  Heating the milk causes splashes inside the carafe. This is

normal.  

•  The hot chocolate quantity in the cup will vary varying the

density:  if  you choose thick density, there will be fewer 

chocolate than that contained in the cup if choosing the 
other densities.

A few seconds may elapse between Energy Saving and delivery 
of the first drink. 

Filling and attaching the milk container 
1.  Press the release buttons and lift the milk container lid  

(fig. 25).

2.  Fill the milk container with a sufficient quantity of milk, 

not exceeding the MAX level (fig. 26).

For a richer denser froth, use skimmed or partially skimmed 
milk at refrigerator temperature (about 41°F/5°C).
To avoid milk with poor froth or large bubbles, always clean 
the milk lid and hot water nozzle as described in the section 
“Cleaning the milk container” on page 16.  
3.  Make sure the milk intake tube is correctly inserted in the 

bottom of the milk container lid  (fig. 27).

4.  Attach the lid back on the milk container. 
5.  Attach the container to the nozzle, pushing as far as it will 

go (fig. 28).

6.  Place a sufficiently large cup under the coffee spouts and 

frothed milk spout (fig. 29). To use particularly tall cups/
glasses, lift the coffee and milk spouts (fig. 30). 

7.  Follow the instructions below for each function.  

Adjusting the amount of froth 
Turn the froth adjustment dial on the milk container lid to 
adjust the amount of froth on the milk delivered while making 
milk drinks (fig. 31).  Follow the tips given in the following 
table:

Dial 
position 

Description

Recommended for…

No froth

CAFFELATTE / 
MILK (hot milk)

Min. froth

LATTE MACCHIATO

Max. froth

 CAPPUCCINO / 
MILK (frothed milk)

Making caffelatte/cappuccino/latte macchiato/milk 
1.  Press the icon corresponding to the required drink. 
2.  After a few seconds, frothed milk is delivered from the 

milk spout into the cup below. Delivery of milk stops 
automatically and (if needed for the drink), coffee 

Thick density 

Medium density 

Thin density