Whirlpool Cooktop W10526085A インストールガイド
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Tools needed
Parts supplied
■
Gas pressure regulator
■
Burner grates
■
Burner caps
■
Clamping brackets (2)
■
2
¹⁄₂" (6.4 cm) clamping screws (2)
Parts needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See “Electrical Requirements” and
“Gas Supply Requirements” sections.
supply and electrical supply. See “Electrical Requirements” and
“Gas Supply Requirements” sections.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances. Do
not obstruct flow of combustion and ventilation air.
not obstruct flow of combustion and ventilation air.
■
It is the installer’s responsibility to comply with installation
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the underside of the
cooktop base.
clearances specified on the model/serial rating plate. The
model/serial rating plate is located on the underside of the
cooktop base.
■
To eliminate the risk of burns or fire by reaching over heated
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
■
The cooktop should be installed in a location away from
strong draft areas, such as windows, doors and strong
heating vents or fans.
strong draft areas, such as windows, doors and strong
heating vents or fans.
■
All openings in the wall or floor where cooktop is to be
installed must be sealed.
installed must be sealed.
■
Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
Given dimensions are minimum clearances.
■
Grounded electrical supply is required. See “Electrical
Requirements” section.
Requirements” section.
■
Proper gas supply connection must be available. See “Gas
Supply Requirements” section.
Supply Requirements” section.
■
The cooktop is designed to hang from the countertop by its
side flanges.
side flanges.
■
The gas and electric supply should be located as shown in
“Installation Clearances” section so that they are accessible
without requiring removal of the cooktop.
“Installation Clearances” section so that they are accessible
without requiring removal of the cooktop.
■
Provide cutout in right rear corner of cutout enclosure as
shown to provide clearance for gas inlet, power supply cord,
and to allow the rating label to be visible.
shown to provide clearance for gas inlet, power supply cord,
and to allow the rating label to be visible.
IMPORTANT: To avoid damage to your cabinets, check with your
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage.
builder or cabinet supplier to make sure that the materials used
will not discolor, delaminate or sustain other damage.
Product Dimensions
■
Tape measure
■
Flat-blade screwdriver
■
³⁄₃₂" (#0 [2 mm]) flat-blade
screwdriver (screwdriver
shaft must be a minimum of
2" [5.1 cm] long)
screwdriver (screwdriver
shaft must be a minimum of
2" [5.1 cm] long)
■
¹⁵⁄₁₆" combination wrench
■
Pipe wrench
■
Wrench or pliers
■
Needle-nose pliers
■
Marker or pencil
■
Pipe-joint compound
resistant to LP gas
resistant to LP gas
■
Noncorrosive leak-detection
solution
solution
A. Model/serial rating plate
A
A. 30
³⁄₁₆
" (76.7 cm) on 30" (76.2 cm) models,
36
¹⁄₄
" (92.0 cm) on 36" (91.4 cm) models
B. 21" (53.3 cm)
C. 3" (7.6 cm)
A
B
C